FUTABA 12K - Page 81

81
<Functions of Linkage Menu>
ŏ6HOHFWWKHIXQFWLRQQDPH
DQGUHWXUQWRWKH/LQNDJH
PHQXE\SXVKLQJWKH RTN
EXWWRQRUSXVKLQJWKH
HOME/EXITEXWWRQ
<Push Dial>
RETURN
FUNCTION
&KDQQHODVVLJQPHQWRIHDFKIXQFWLRQFDQEHFKDQJHG
When you select model and wing (swash) types,
you will find that the optimized combinations of
servo output channels and functions have been
already preset. If you would like, you can freely
change combinations of servo output channels,
functions (aileron, elevator, etc), and control (sticks,
switches, and trim levers).
*You can also assign the same function to multiple servo
output channels such as assigning elevator function to CH2
and CH3.
Channel Replacement
When the channel is replaced in the Function
menu, replaced channel uses the setting data (ATV,
SUB-TRIM, REVERSE, F/S, and B-F/S, etc.).
Servo Output Channels
For T-FHSS Air 14CH mode, you can set 12
linear channels and two digital channels. For
S-FHSS mode, you can set only 8 linear channels.
Function change
0RYHWKHFXUVRUWRWKHIXQFWLRQLWHPRIWKH
FKDQQHO\RXZDQWWRFKDQJHDQGSXVKWKH
571EXWWRQ
*The function selection screen is displayed.
0RYHWKHFXUVRUWRWKHIXQFWLRQQDPH\RX
ZDQWWRVHWDQGSXVKWKH571EXWWRQ
*The function name blinks.
3XVKWKH571EXWWRQWRH[HFXWHWKHFKDQJH
:KHQ\RXZDQWWRFDQFHOWKLVRSHUDWLRQ
SXVKWKH6EXWWRQ
*Multiple channels can be assigned to one function.
*DG1/2 (digital channels)
These channels can function as switched channels. You can
freely change combinations between servo output channels
and input controls (sticks, switches, and trim levers).
Motor Function
If you have either a Glider or Airplane Model
Type selected, and choose to activate the Motor
function, a reverse setting screen is displayed.
*If YES is selected, the output is reversed. If NO is selected,
the output is normal.
:DUQLQJ
As a safety precaution to prevent the motor
from starting unexpectedly, please switch
off the motor accordingly. We also suggest
removing the propeller from the motor as an
additional precaution.
Operation control change
0RYHWKHFXUVRUWRWKH&75/LWHPRIWKH
FKDQQHO\RXZDQWWRFKDQJHDQGSXVKWKH
571EXWWRQ
*The control selection screen is displayed.
0RYHWKHFXUVRUWRWKHFRQWURO\RXZDQWWR
FKDQJHDQGSXVKWKH571EXWWRQ
*The same control can be assigned to multiple channels.
(The display screen is an example. The
screen depends on the model type.)
ŏ6HOHFW>)81&7,21@LQWKH/LQNDJHPHQXDQG
DFFHVVWKHVHWXSVFUHHQVKRZQEHORZE\SXVKLQJ
WKH571EXWWRQ
ŏ7ULPRSHUDWLRQPRGH
&20%&RPELQDWLRQPRGH
6(3$56HSDUDWHPRGH
,WVHWVXSE\T1-T4 SETRI/,1.$*(0(18
6FUROOLQJ
ŏ0RYLQJFXUVRU
ŏ6HOHFWLQJPRGH
ŏ$GMXVWLQJYDOXH
ŏ7RQH[WSDJH