FUTABA T4PM

ON/OFF Position (POSI)
5 ~ 95
Initial value: 50
Shows the ON/OFF state
105
Function
CPS Mixing "CPS MIX"
1
(Control system setup)
Select the setting item "CTRL" by moving the (JOG) button up
or down. Use the (+) or (-) button and select the function.
"
INH
"
 )XQFWLRQ2))
"
&+)81&
"
212))E\VZLWFKVHWDWWKHWK&+
"
STR NT
"
 21DWVWHHULQJQHXWUDO
"
STR END
"
 21DWERWKVLGHVRIVWHHULQJ
"
THR NT
"
 21DWWKURWWOHQHXWUDO
"
7+5):'
"
 21DWWKURWWOHIRUZDUGVLGH
"
7+5%5.
"
 21DWWKURWWOHEDFNEUDNHVLGH
"
7+17%.
"
21DWWKURWWOHQHXWUDODQGEDFNEUDNHVLGHV
:KHQ
"
(6&0,;$&7
→
,1+
"
LV GLVSOD\HGWKH &3&0,; FDQQRWEH XVHGLI WKH
'8$/(6&IXQFWLRQLVQRWVHWWR
"
INH
"
.
:KHQ
"
6750,;$&7
→
,1+
"
LVGLVSOD\HGWKH&360,;FDQQRWEHXVHGLIWKH
STR MIX function is not set to
"
INH
"
.
:KHQ
"
%5.!$&7
→
,1+
"
 LVGLVSOD\HG WKH &360,; FDQQRW EHXVHG LI WKH
%5$.(0,;&+IXQFWLRQLVQRWVHWWR
"
INH
"
.
2
(ON/OFF switching position selection)
Select the setting item "POSI" by moving the
(JOG) button up or down. Use the (+) or (-) but-
ton and select the ON/OFF position. Since the
ON/OFF state is displayed at the right side of
the setting item "CTRL", setting can be con-
firmed while operating the function to be con-
trolled (for example, throttle).
3
(ON/OFF type setup)
Select the setting item "TYPE" by moving the (JOG) button up
or down. Use the (+) or (-) button and select the type of LED
lighting. Normal ON/Off type or fl ashing can be selected.
"
1250$/
"
1RUPDO212))W\SH
"
)/$6+
"
 )ODVKLQJGLVSOD\
4
(Flashing cycle setting)
When flashing type "FLASH" is selected at the setting item
"TYPE", the flashing speed (cycle) can be set.
Select the setting item "CYCL" by moving the (JOG) button up
or down. Use the (+) or (-) button and select the flashing speed
(cycle).
5
When finished with the setting, return to the MENU screen by
pressing the (END) button.
Select button
- Select with the (+) or (-) but-
tons.
Adjust button
- Use the (+) and (-) buttons to
make adjustments.
- Return to the initial value by
pressing the (+) and (-) buttons
simultaneously (approx. 1 sec).
Select button
- Select with the (+) or (-) but-
tons.
Function selection (MODE)
INH, CH4 FUNC, STR NT, STR
END, THR NT, THR FWD, THR
BRK, TH NT+BK
Function selection (TYPE)
NORMAL, FLASH
Flashing cycle (CYCL)
1 ~ 100
Initial value: 50