FUTABA T4PM

47
Function
Warning

Operate each servo over its full stroke and be sure the
linkage does not bind or is not loose.
The continuous application of unreasonable force to a servo may
cause damage and excessive battery drain.
End Point Adjuster "END POINT"
(All channel)
8VHWKLVZKHQSHUIRUPLQJOHIWDQGULJKWHQGSRLQWDGMXVWPHQWVWKURWWOHKLJKVLGHEUDNH
VLGHRSHUDWLRQDPRXQWDGMXVWPHQWRUFKDQQHODQGFKDQQHOVHUYRXSVLGHGRZQVLGH
RSHUDWLRQDPRXQWDGMXVWPHQWGXULQJOLQNDJH
&RUUHFWWKHPD[LPXPVWHHULQJDQJOHIRUOHIWDQGULJKWVWHHULQJDQJOHVZKHQWKHUHLVD
difference in the turning radius due to the characteristics of the vehicle.
The
"
(1'32,17
"
function basically determines the maximum steering angle of
each channel.
7KHIXQFWLRQVVKRZQEHORZPD\KDYHEHHQDGMXVWHGRUWKHRSHUDWLQJUDQJHVHWE\
"
(1'32,17
"
IXQFWLRQPD\EHH[FHHGHG&KHFNWKHOLQNDJHHDFKWLPHWKHIROORZ-
LQJIXQFWLRQVDUHDGMXVWHG
6XEWULPDOOFKDQQHOV ...........................................page 46
7KURWWOHDFFHOHUDWLRQWKURWWOH ...............................SDJH
5HIHUWRFRXQWU\GLVWULEXWRU:(%IRUGHWDLOHGWKHIROORZLQJIXQFWLRQH[SODQDWLRQ
,GOHXSWKURWWOH7KURWWOHRII(QJLQH&XWWKURWWOH
3URJUDPPL[LQJVODYHVLGHDOOFKDQQHOV
Maximum steering angle
$7/WULPDOORZVDGMXVWPHQWRIWKHEUDNHVLGHRSHUDWLRQDPRXQWGXULQJRSHUDWLRQ
7KHUHIRUHZKHQWKHRSHUDWLQJDQJOHLVDGMXVWHGZLWKWKURWWOH(1'32,17$7/
trim must also be taken into account.
ATL trim
End Point Adjuster "END POINT"
$GMXVWWKHWKURWWOHVHUYRVRWKDWXQUHDVRQDEOHIRUFHLVQRWDSSOLHGZKHQWKHHQJLQHFDUEXUHWRULVIXO-
O\RSHQIXOO\FORVHGDQGWKHEUDNHVDUHDSSOLHGIXOO\
,IWKHEUDNHVRYHUKHDWZKLOHUXQQLQJWKHLUDELOLW\WRIXQFWLRQSURSHUO\GHFUHDVHV%HIRUHUXQQLQJ
DGMXVWWKHVXLWDEOHPD[LPXPVHUYRWUDYHOVRWKDWXQUHDVRQDEOHIRUFHLVQRWDSSOLHGHYHQZKHQWKH
VHUYRWUDYHOLVLQFUHDVHGZKLOHUXQQLQJ
$GMXVWWKHVWHHULQJ VHUYR VRWKDWXQUHDVRQ-
able force is not applied to the servo by the
chassis at maximum servo travel.
Decide the END POINT
value at the contact point.
Caution!
A whining noise indicates that the
steering servo is improperly set.