FUTABA T4PM

64
Function
Warning display
The function select switch
screen (page 100) can be
displayed from this screen.
< NO SW >
If function’s ON/OFF switch
is not selected, <NO SW>
is displayed.
(Preparation)
- Use the function select switch to select the switch. (page 92)
1
(Neutral brake rate)
Select the setting item "NTBRK" by moving the (JOG) button
up or down. Use the (+) and (-) buttons to set the neutral brake
rate.
2
When finished with the setting, return to the MENU screen by
pressing the (END) button.
Neutral Brake function adjustment
7KH(6&QHXWUDOEUDNHIXQFWLRQDQG739QHXWUDOEUDNHIXQFWLRQFDQEHXVHG VL
PXOWDQHRXVO\+RZHYHUZKHQVHWWLQJLVGLI¿FXOWWRXQGHUVWDQGZHUHFRPPHQGWKDW
only one neutral brake function be used.
Reference
Throttle Mode "TH MODE"
:KHQWKHQHXWUDOEUDNHIXQFWLRQLV
"
21
"
WKH neutral EUDNHUDWHDGMXVWPHQWLVDXWR
PDWLFDOO\DVVLJQHGWRWKHWKURWWOHWULP'7
-
'7RU'/
Dial / Trim Setting
7KURWWOHVLGH(3$IXQFWLRQRU$7/IXQFWLRQVHWWLQJDOVRDIIHFWVQHXWUDOEUDNHVLGH
operation.
Effect of set value of other functions on neutral brake
Neutral Brake "NTBRK"
7KLVLVDIXQFWLRQVHOHFWVZLWFKIXQFWLRQ7KHQHXWUDOEUDNHIXQFWLRQ212))VZLWFK
PXVWEHVHWVHHSDJH
7KHQHXWUDOEUDNHZKLFKDSSOLHVWKHEUDNHVDWWKHQHXWUDOSRVLWLRQRIWKHWKURWWOHWULJ
JHUFDQEHVHW+RZHYHUZKHQXVLQJWKH0&&50&&0&&0&&5
RURWKHU)XWDED(6&FRQ¿UPWKDWWKH(6&LVLQWKHQHXWUDOSRVLWLRQDQGWKHVHWLVLQWKH
RSHUDWLRQPRGHEHIRUHVHWWLQJWKHQHXWUDOEUDNHIXQFWLRQVZLWFKWR21WKHVDPHDVWKH
LGOHXSIXQFWLRQSDJH,QDGGLWLRQZKHQWKHLGOHXSIXQFWLRQRUWKURWWOHRIIIXQF
WLRQSDJHLVVHWWKLVIXQFWLRQKDVDKLJKHUSULRULW\WKDQWKHQHXWUDOEUDNHIXQFWLRQ
$Q/('EOLQNVZKLOHWKHQHXWUDOEUDNHIXQFWLRQLVDFWLYH
Operation display
,IWKHSRZHUVZLWFKLV
WXUQHGRQZKLOHWKH
QHXWUDOEUDNHVZLWFKLV
RQDQDXGLEOHDODUP
ZLOOEHKHDUG,PPH
diately set the neutral
EUDNHVZLWFKWR2))
Adjust button
- Adjust with the (+) and (-) but-
tons.
- Return to the initial value "0" by
pressing the (+) and (-) buttons
simultaneously for about 1 sec-
ond.
Brake rate (NTBRK)
0 ~ B100
Initial value: 0