FUTABA T4PM

59
Function
AB.P
(Amount of brake return)
AB.P
Servo travel
A.B.S. Function "TH A.B.S"
- DELY : Delay
6HWVWKHGHOD\IURPEUDNHRSHUDWLRQWR$%6RSHUDWLRQ:KHQVHWWRWKH$%6
IXQFWLRQLVDFWLYDWHGZLWKRXWDQ\GHOD\$WWKH$%6IXQFWLRQLVDFWLYDWHGDIWHU
DGHOD\RIDSSUR[LPDWHO\VHFRQGDQGDWWKH$%6IXQFWLRQLVDFWLYDWHGDIWHUD
delay of approximately 2 seconds.
- CYCL : Cycle speed
6HWVWKHSXOVHVSHHGF\FOH7KHVPDOOHUWKHVHWYDOXHWKHIDVWHUWKHSXOVHF\FOH
- TG.P : Trigger point
6HWVWKHWULJJHUSRLQWDWZKLFKWKH$%6IXQFWLRQEHJLQVWRRSHUDWHDWEUDNHRSHUDWLRQ
- DUTY : Cycle duty ratio
Sets the proportion of the time the brakes are applied and the time the brakes are re-
OHDVHGE\SXOVHRSHUDWLRQ7KHUDWLRFDQEHVHWWR+,*+0,'RU/2:
- MODE : Function ON/OFF
$%6IXQFWLRQ212))VHWWLQJ:KHQXVLQJWKH$%6IXQFWLRQVHWWR
"
$&721
"
.
1
(Function ON/OFF)
Select the setting item "MODE" by moving the (JOG) button up
or down. Set the function to the active state by pressing the (+)
or (-) button.
"
,1+2))
"
 )XQFWLRQ2))
"
$&721
"
 )XQFWLRQ21
"
$&72))
"
6ZLWFK2))ZKHQVHWWLQJVZLWFKHV
2
(Brake return amount adjustment)
Select the setting item "AB.P" by
moving the (JOG) button up or
down. Use the (+) or (-) button to
adjust the return amount.
"

"
 1RUHWXUQ
"

"
 5HWXUQWRWKHSRVLWLRQRIWKHEUDNHRSHUDWLRQDPRXQW
"

"
5HWXUQWRWKHQHXWUDOSRVLWLRQ
3
(Delay amount setup)
Select the setting item "DELY" by moving the (JOG) button up
or down. Use the (+) or (-) button to adjust the delay amount.
"

"
 $%6IXQFWLRQSHUIRUPHGZLWKRXWDQ\GHOD\
"

"
 $%6IXQFWLRQSHUIRUPHGDIWHUDQDSSUR[LPDWHVHFGHOD\
"

"
$%6IXQFWLRQSHUIRUPHGDIWHUDQDSSUR[LPDWHVHFVGHOD\
A.B.S function adjustment
- Brake return amount (AB.P) is
influenced by the "EXP" rate
on the brake side.
Delay amount (DELY)
0 ~ 100
Initial value: 0
Adjustment buttons
- Use the (+) and (-) buttons to
make adjustments.
- Return to the initial value by
pressing the (+) and (-) buttons
simultaneously (approx. 1 sec).
Adjustment buttons
- Use the (+) and (-) buttons to
make adjustments.
- Return to the initial value by
pressing the (+) and (-) buttons
simultaneously (approx. 1 sec).
Brake return amount (AB.P)
0 ~ 50 ~ 100
Initial value: 50
Function ON/OFF (MODE)
INH (OFF), ACT (ON,OFF)
Select button
- Select with the (+) or (-) but-
tons.