Need help?Do you have a question about the Garage Smart MY LIFTER BASIC LIFTER and is the answer not in the manual?
General| Brand | Garage Smart |
|---|---|
| Model | MY LIFTER BASIC LIFTER |
| Category | Lifting Systems |
| Language | English |
Garage Smart offers a Limited Lifetime Warranty on all products. Defective hardware or components will be repaired or replaced.
Covers defects in material/workmanship from personal, normal household use. Excludes damage from misuse or accidents.
Does not cover misuse, accidents, commercial use, or unauthorized modifications. Use of other systems voids warranty.
Contact Garage Smart for service. User must ship defective product with defect description for evaluation.
Warranty is in lieu of all other warranties. Liability is limited to purchase price. State laws may grant additional rights.
Read and follow instructions. Avoid moving parts, do not stand under loads, do not lift people or animals.
Maximum lifting capacity is 100 lbs. Stop use immediately if cable is tangled, damaged, or bent.
Failure to follow safety instructions may result in property damage, serious personal injury, or death.
Install only as specified. Do not open casing. Product is for indoor use only. Failure to comply can cause injury or death.
Device complies with FCC Part 15. May cause interference; follow measures to correct if needed.
Device meets general RF exposure requirements and can be used in portable conditions without restriction.
Caution: To reduce risk of electric shock or injury, use indoors only.
Motorized hoist controlled by smart device. Lifts up to 100 lbs per unit, up to 400 lbs with four units.
Scan QR code or follow link for Garage Smart DIY Installation Guides.
Lists necessary tools: ladder, stud finder, tape measure, drill, socket wrench, screwdriver, and safety glasses.
Identifies the Garage Smart Lifter and its accessories: QD Pins, Lag Washer, Lag Screw, Pulley Hook, Eyelet Screw, Drill Bit, Carabiner.
Identifies the Power Adapter and its accessories: DC Power Cable, Universal Mount, Cable Management Clips/Screws.
Decide placement for the Basic Lifter and ensure the Mounting Bracket is centered on a ceiling joist above the item.
Warning: Failure to follow safety instructions may result in property damage, serious personal injury, or death.
Use a stud finder to locate the ceiling joist and ensure adequate clearance for the item being lifted.
Warning: Failure to mount bracket to a secure joist or rafter may result in property damage, injury, or death.
Consider item orientation and mount the bracket accordingly. Refer to figures for correct mounting configurations.
Mark holes on joist, drill at least 3" deep pilot holes through sheetrock into the wood joist.
Warning: Inserting lag screws without pilot holes may split wood, causing damage, injury, or death.
Tighten screws with wrench until snug. Align lifter and insert quick-release pins.
Warning: Do not use an impact driver for lag screws; overtightening can cause failure and injury.
Find a wall location where AC cable reaches outlet and DC cable reaches MyLifter. Use template to place screws 2 inches apart.
Line up mounting holes with screws, place product over screws, and slide to lock. Multiple orientations are possible.
Note: Power adapter may be removed for tighter screw fit. Universal Mount is not for wall mounting.
Peel sticker, stick clip, install screw, place wires in clip, and securely close. Clips hold AC/DC cables.
Plug AC cable into power source. Additional products can be powered via the adapter's AC outlet.
If mounted parallel to joist, place eyelet screw on same side as power plug to prevent cable damage.
If mounted perpendicular, place eyelet screw on same side as cable guide opening to prevent cable damage.
Locate stud center, pre-drill hole, insert eyelet screw, and tighten. Follow specific instructions for drywall/no drywall.
Warning: Failure to insert eyelet screw into a secure joist or rafter may result in property damage, injury, or death.
Run cable under pulley, use carabiner to anchor cable to eyelet screw. Required for loads over 50 lbs.
Download MyLifter App from Google Play/App Store. Open app and tap 'Add Devices' button.
Follow on-screen prompts, tap 'Got It'. Lifter indicator light changes to fast green-blink upon successful pairing.
Paired lifter icon changes to filled-in image. Tap back arrow to return to the main screen.
Warning: Do not stand under the unit while operating. Keep body parts away from moving parts.
Navigate to the app main screen, tap Edit. For Android, tap pencil icon and Submit. For iOS, select Lifter and Save.
From app main screen, tap Edit. Android: Tap trash can icon, then Yes. iOS: Tap minus icon, then Delete.
Explains Set High/Low points, Weight Gauge, Variable Speed Controller, and Manual Lift/Lower Arrows.
Use manual arrows to lift/lower. Use variable speed control circle to adjust speed during operation.
Reach desired point using manual arrows, then tap SET LOW/SET HIGH and 'Set' to save.
Note: Exceeding capacity (50/100 lbs) stops lifting; check for obstructions or remove weight.
Warning: Do not lower more weight than lift capacity. Do not add objects to lifted item; risk of damage/injury/death.
Tap SMART LOWER/SMART LIFT to reach preset positions. Tap SET LOW/SET HIGH and Clear to reset points.
Note: During Smart Lift/Lower, controls change to STOP button. Tap STOP to halt operation.
How much weight can the Basic Lifter hold? Up to 100 lbs. Do not exceed designed weight limit with multiple lifters.
Why is my load tilting? Move the lifter towards the lower side of the load until it lifts level.
To Next Page
