GE 10 - User Manual

Installation
Instructions
Gas Dryer
10
Questions on Installation? Call: 800.GE.CARES (US) or 800-561-3344 (Canada)
or visit our web site at: www.GEAppliances.com (US)
BEFORE YOU BEGIN
Read these instructions
completely and carefully.
« IMPORTANT- save
these instructions for local
inspector's use.
e IMPORTANT- observe
all governing codes and
ordinances.
¢ Note to Installer - Be sure to
leave these instructions with
the customer.
* Note to Customer - Keep these
instructions with your Owner’s
Manual for future reference.
* Before the old dryer is removed
from service or discarded,
remove the dryer door.
e Service information and the
wiring diagram are located in
the control console.
¢ Do not allow children on
or in the appliance. Close
supervision of children is
necessary when the appliance
is used near children.
e Install the dryer where the
temperature is above 50°F for
satisfactory operation of the
dryer control system.
* Product failure due to
improper installation is not
covered under the Warranty.
AWARNING aisk oF Fire
* To reduce the risk of severe injury or death, follow all installation instructions.
* Clothes dryer installation must be performed by a qualified installer.
* Install the clothes dryer according to these instructions and in accordance with local
codes.
¢ California Safe Drinking Water and Toxic Enforcement Act
This act requires the governor of California to publish a list of substances known to the
state to cause cancer, birth defects or other reproductive harm and requires businesses
to warn customers of potential exposure to such substances. Gas appliances can
cause minor exposure to four of these substances, namely benzene, carbon monoxide,
formaldehyde and soot, caused primarily by the incomplete combustion of natural gas
or LP fuels. Properly adjusted dryers will minimize incomplete combustion. Exposure to
these substances can be minimized further by properly venting the dryer to the outdoors.
* This dryer must be exhausted to the outdoors.
* Use only rigid metal 4” diameter ductwork inside the dryer cabinet and use only UL
approved transition ducting between the dryer and the hore duct.
# DO NOT install a clothes dryer with flexible plastic ducting materials. If flexible metal
(semirigid or foil-type) duct is installed, it must be UL listed and installed in accordance
with the instructions found in “Connecting The Dryer To House Vent” on page 5 of this
rnanual. Flexible venting materials are known to collapse, be easily crushed, and trap
lint. These conditions will obstruct dryer airflow and increase the risk of fire.
¢ Do not install or store this appliance in any location where it could be exposed to
water and or weather.
* Save these instructions. (Installers: Be sure to leave these instructions with the
customer).
IN THE COMMONWEALTH OF MASSACHUSETTS
* This product must be installed by a licensed plumber or gas fitter.
« When using ball-type gas shut-off valves, they shali be the T-handle type.
¢ A flexible gas connector, when used, most not exceed 3 feet.
MATERIALS YOU WILL NEED
c
4" DIA. METAL PIPE
ELBOW
4" DIA, METAL DUCT
[RECOMMENDED}
TOOLS YOU WILL NEED
S (x2) ee
10" ADJUSTABLE WRENCHES
ee 4" SPRING
i
Soman
yy
CLAMPS
(2}
D
TDD,
FLAT
BLADE
SCREWDRIVER
~\
yp,
&S
ye
8" BIDE WRENCH 4" DIA FLEXIBLE METAL FOIL TYPE ( ms»
SLIP JOINT PLIERS
EXHAUST COMPOUND SOAP SOLUTION
HOOD
DD we FOR LEAK DETECTION
0 FLEE Neva Sen GD NG) Se]
ULUSTED TraNsrioN DUCT eoua
KIT WxO8K10077 INCLUDES 2 ELsows} CLAMPS (2) DUCT TAPE SAFETY
oR GLASSES
UL LISTED TRANSITION DUCT Mo Zt
HIE NEEDED | FLEXIBLE GAS LINE CONNECTOR — GLOVES
Step 1
Step 2
(see section 1).
Step 3
section 6).
Step 4
Step 5
Step 6
Step 7
(see section 4).
Step 8
Verify your gas installation (see section 2).
Prepare the area and exhaust for installation of new dryer
Check and ensure the existing external exhaust is clean (see
section 1) and meets attached installation specifications (see
Remove the foam shipping pads (see section 1).
Move the dryer to the desired location.
Level your dryer (see section 8).
Connect the gas supply (see section 3} and check for leaks
Connect the external exhaust (see section 7).
Step 9 Connect the power supply (see section 5}.
Step 10 Check the operation of the power supply, gas connections,
and venting.
Step 11 Place the Owner's Manual and the Installation Instructions in
a location where they will be noticed by the owner.
For alcove or closet installation, see section 9.
For bathroom or bedroom installation, see section 10.
For mobile or manufactured home, see section 11.
For garage installation (if allowed by local codes], see section 12.
For side or bottom exhaust, see section 13.
254D1052P006 31-16630-2 08-11 GE

GE 10 Specifications

General

Brand	GE
Model	10
Category	Dryer
Language	English