What to do if GE ZTS Switch engine does not stop?
If your GE Switch engine won't stop, it could be due to several reasons. The U timing cycle might not be complete, so check the U timer setting. Another possible cause is incorrectly terminated engine start wires, in which case you should check the engine start connections. Finally, ensure the generator is not in MANUAL; place it in AUTO.
Why GE Switch ATS will not transfer to SOURCE 2?
If the GE Switch's ATS won't transfer to SOURCE 2, it might be due to several factors. The voltage or frequency of SOURCE 2 might not be within acceptable parameters; in this case, check the engine start connections, generator breaker, generator output, and engine control switch. Also, ensure the power supply connector is plugged in. Finally, check the WTimer setting, as the W timing cycle might not be complete.
What to do if GE Switch ATS will not transfer to SOURCE 1?
If the GE Switch's ATS won't transfer to SOURCE 1, it might be because the DW timing cycle is not complete. Check the DWTimer setting to resolve this issue.
How to troubleshoot GE ZTS if the engine does not start?
If your GE Switch engine won't start, check the engine start connections to ensure they are properly terminated. Also, investigate why the Engine Control Switch was turned off, as the generator might be in the OFF position.
General safety guidelines for operating the transfer switch.
Procedures and considerations for installing the transfer switch.
Procedures for maintaining and testing the switch.
Guide for identifying and resolving switch issues.
Warning about severe injury or death from hazardous voltage.
Instructions for inspecting and storing the transfer switch.
Precautions for installation, including mounting and drilling.
How to connect power conductors to the transfer switch terminals.
Connecting engine start control wires to designated terminals.
Step-by-step procedure for initial energization of the switch.
Verifying source voltage and frequency before energization.
Completing setup and visual inspection before final energization.
Details on control connections to the microcontroller and field wiring.
Components and functions of the microprocessor assembly.
Components and purpose of the R/T box.
Navigating options via LCD screen and keypad for settings.
Adjusting 'Fail' and 'Restore' points for Source 1 voltage/frequency.
Adjusting 'Fail' and 'Restore' points for Source 2 voltage/frequency.
Definitions and functions of accessories like 6P, 6A, A1, etc.
Continued definitions of accessories, including M1, M2, P1, Q2, etc.
Further definitions for accessories like R50, S5P, S12P, T, U.
Step-by-step guide to set the system clock, time, and date.
How to configure and set the CDT timer exerciser parameters.
Procedures for initiating, bypassing, and checking CDT exercises.
How to configure and set the CDP clock exerciser parameters.
Procedures for bypassing and checking CDP exerciser events.
Turning optional accessories ON or OFF via the CFG menu.
Changing adjustable values for system clock, timers, and voltages via SET menu.
How to view system voltage, frequency, exerciser status, and event logs.
Steps for performing ATS tests including XFR LOAD, FAST TEST, and NO XFR.
Test sequences for Standard and Delayed Transition operations.
Detailed sequence for standard transition during power failure and restoration.
Detailed sequence for delayed transition during power failure and restoration.
Layout and bill of materials for standard transition R/T boxes.
Layout and bill of materials for delayed transition R/T boxes.
Wiring diagrams for standard and delayed transition R/T box components.
Warning about severe injury or death from hazardous voltages during troubleshooting.
Guide for recognizing, determining, and resolving basic switch faults.
Cautions and steps for inspection, cleaning, and servicing the switch.
Manual and electrical testing of the transfer switch, including timers.
Diagram showing the layout of the standard control panel (SSRCP).
Identification of individual relays mounted on the control panel.
How to adjust solid state timers for timing cycles.
Adjusting the VFSM for pickup and fail points.
Adjusting ARSM relay for restore and dropout points.
To Next Page
General
