Page 8 (Drive Layout)

Genesis KBWA-23D - Drive Layout

Genesis KBWA-23D

36 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

8

FIGURE 2

DRIVE LAYOUT

(SHOWN WITH COVER REMOVED)

Table of Contents

Table of Contents4
Familiarizing Yourself with the Drive7
Cover Layout7
Drive Layout8
Electrical Ratings and Specifications9
Electrical Ratings9
General Performance Specifications9
Introduction10
- Standard Features11
- Performance Features11
- Protection Features12
- Selectable Jumpers12
- Adjustable Trimpots12
- Customization for Oems13
Important Application Information13
- 50 Hz Motors13
- Motor Current Setting13
Factory Setting of Current Limit (CL) Trimpot13
- Motor with External Fan Cooling14
Maximum Allowed Motor Torque Vs. Speed14
- Electronic Motor Overload Protection15
Open Ventilated Motor with External Fan Cooling15
Removing and Installing the Cover16
- Removing the Cover16
- Installing the Cover17
Cover Positioned on Top of Case17
Forward-Stop-Reverse Switch Installation18
Installing the Supplied Forward-Stop-Reverse Switch (Required for Manual Start Mode)18
AC Line Input Voltage Selection19
- Setting the Drive for Two Times the Rated Motor RPM20
Setting Selectable Jumpers19
- AC Line Input Voltage Selection (Jumper J3)19
- 60 Hz and 50 Hz Motor Operation and Drive Output Frequency Selection (Jumpers J1 and J2)19
  - Setting the Drive for 60 Hz and 50 Hz Motor Operation19
60 Hz and 50 Hz Motor Selection20
Available Torque Vs. Output Frequency20
- Automatic and Manual Start Mode (CON1)21
  - Automatic Start Mode21
120 Hz and 100 Hz Drive Output Frequency Selection21
Automatic Start21
- Manual Start Mode22
- Forward/Reverse Speed Selection (CON2)22
Manual Start22
Forward/Reverse Speed Selection22
Mechanical Specifications23
Mounting23
Electrical Connections24
- 10.1 Ac Line Input and Ground25
- 10.2 Motor and Ground25
Reconditioning the Bus Capacitors24
Terminal Block TB1 Wire and Tightening Torque Specifications25
- 10.3 Ac Line Input Fusing26
AC Line Input, Motor, and Ground Connections26
High Voltage Dielectric Withstand Test (Hi-Pot)27
DC Hi-Pot Tester Setup Information27
Trimpot Adjustments28
Typical Hi-Pot Test Setup28
- Minimum Speed Trimpot (MIN)29
- Maximum Speed Trimpot (MAX)29
- Acceleration Trimpot (ACC)29
Minimum Speed Trimpot (MIN) Range29
Maximum Speed Trimpot (MAX) Range29
Acceleration Trimpot (ACC) Range29
- Deceleration Trimpot (DEC)30
- Slip Compensation Trimpot (COMP)30
Deceleration Trimpot (DEC) Range30
Slip Compensation Trimpot (COMP) Range30
- Current Limit Trimpot (CL)31
KBWA-23D CL Trimpot Range31
KBWA-22D CL Trimpot Range31
KBWA-21D CL Trimpot Range31
KBWA-2P6D CL Trimpot Range31
KBWA-2P3D CL Trimpot Range31
Drive Operation32
- 13.1 Start-Up Procedure32
- 13.2 Fault Recovery32
- Restarting the Drive after an Overload Fault Has Cleared33
Diagnostic Indicators33
Fault Recovery and Resetting the Drive33
- 14.1 Illuminated On/Off Ac Line Switch34
- Power on LED (PWR)34
- Status LED (ST)34
Operating Condition and Status LED Indicator34

EasyManua.ls – Your Ultimate Manuals Destination!

With a comprehensive collection of over 1 million PDF manuals, service guides, instruction booklets, and quick start guides, we cover every aspect of your needs. Explore manuals for products from more than 50,000 brands all in one place. Search and instantly view the manual you’re looking online for free.

Privacy Policy
Contact Us

© Copyright 2025 EasyManua.ls. All Rights Reserved.