How to fix a Relay-Check Failure on a Goodwe GW5000D-NS Inverter?
To address a Relay-Check Failure on your Goodwe Inverter: 1. Turn off the DC switch of the inverter. 2. Wait until the LCD light is off. 3. Turn on the DC switch and ensure it is connected.
What does Fac Failure mean on Goodwe Inverter?
A 'Fac Failure' on your Goodwe Inverter means it is not connected to the grid. Check if the power grid is connected to the cable, and check the availability of the power grid.
What does Ground I Failure mean on Goodwe GW5000D-NS, and how can it be fixed?
A 'Ground I Failure' on your Goodwe Inverter indicates that the ground current is too high. Unplug the inputs from the PV generator and check the peripheral AC system. Once the problem is resolved, reconnect the PV panel and check the inverter status.
What to do if my Goodwe GW5000D-NS has no display?
If your Goodwe Inverter's display is not working: 1. Turn off the DC switch and unplug the DC connector, then measure the voltage of the PV array. 2. Plug in the DC connector and turn on the DC switch. 3. If the PV array voltage is lower than 250V, check the configuration of the inverter module.
What to do if my Goodwe Inverter shows 'Isolation Failure'?
If your Goodwe inverter displays an 'Isolation Failure', follow these steps: 1. Check the impedance between the ground and PV (+) & PV (-). The impedance value must be greater than 100kΩ. Ensure the inverter is properly grounded. 2. If the problem persists, contact your local service office for assistance. Additionally, the inverter has a built-in buzzer that will sound continuously for 1 minute upon failure. If the fault isn't resolved, the buzzer will sound every 30 minutes. You can also add the inverter to a monitoring platform and set up alarm reminders to receive email notifications about alarm information.
What to do if my Goodwe GW5000D-NS Inverter displays 'Vac Failure'?
If your Goodwe inverter is showing a 'Vac Failure', here are some things to check: 1. The PV Inverter will automatically restart within 5 minutes if the grid returns to normal. 2. Ensure that the grid voltage conforms to the specified requirements. 3. Verify that the neutral (N) wire and PE cable are properly connected. 4. If the problem persists, contact your local service office for further assistance.
What to do if my Goodwe Inverter displays 'Utility Loss'?
If your Goodwe inverter indicates a 'Utility Loss', please check the following: 1. Ensure the inverter is properly connected to the power grid. 2. Verify that the power grid is connected to the cable. 3. Confirm the availability of the power grid.
What to do if my Goodwe Inverter shows a Vac Failure?
If your Goodwe Inverter displays a Vac Failure, it means there's an issue with the grid voltage. First, the inverter will automatically restart within 5 minutes if the grid returns to normal. Ensure the grid voltage conforms to the specified requirements. Also, verify that the neutral (N) wire and PE cable are securely connected.
What to do if my Goodwe Inverter displays 'PV Over Voltage'?
If your Goodwe inverter is showing a 'PV Over Voltage' error: 1. Check if the PV open circuit voltage is higher than or too close to the maximum input voltage. 2. If the issue persists even when the PV voltage is less than the maximum input voltage, contact your local service office for assistance.
Why does my Goodwe GW5000D-NS have no display?
If your Goodwe inverter's display is not working, try these steps: 1. Turn off the DC switch and unplug the DC connector, then measure the voltage of the PV array. 2. Plug in the DC connector and turn on the DC switch. 3. If the PV array voltage is lower than 250V, check the configuration of the inverter module. 4. If the voltage is higher than 250V, contact your local service office for assistance.
Overview of GoodWe NS & DNS series inverters, highlighting technology, design, and size.
Explains the evolution of single-phase inverters and compares SS/DS with NS/DNS series.
Details key features like safety, lower start-up voltage, and integrated communication.
Instructions for mounting, package contents, and selecting installation locations.
Step-by-step guide for starting up the inverter and configuring WiFi monitoring.
Block diagrams illustrating the internal components of NS and DNS series inverters.
Common error codes, causes, and measurement procedures for troubleshooting inverter issues.
Detailed specifications for NS and DNS series inverters, including DC/AC input/output and efficiencies.
Overview of product certifications and approvals across different regions and standards.
Information on standard warranty conditions, exceptions, and after-sales service policies.
General| Model | GW5000D-NS |
|---|---|
| Rated Power | 5000 W |
| Max. DC Input Power | 6500W |
| Number of MPPT | 2 |
| Max. Input Current per MPPT | 13 A |
| Rated AC Output Power | 5000 W |
| Max. AC Apparent Power | 5500 VA |
| AC Voltage Range | 180-280V |
| Total Harmonic Distortion (THD) | <3% |
| DC Switch | Yes |
| Protection Class | IP65 |
| Protection Level | IP65 |
| Rated Output Voltage | 230 V |
| AC Output Voltage | 230 V |
| Rated Grid Frequency | 50 Hz |
| AC Output Frequency | 50 Hz |
| Power Factor | >0.99 |
| Operating Temperature Range | -25°C to 60°C |
| Cooling Method | Natural Convection |
To Next Page
