EasyManua.ls Logo

Graco ProControl 1KE Plus - User Manual

Graco ProControl 1KE Plus
90 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Instructions-Parts
ProControl™ ProControl™
ProControl™
1KE 1KE
1KE
Plus Plus
Plus
Models Models
Models
for for
for
Management Management
Management
of of
of
Fluid Fluid
Fluid
and and
and
Air Air
Air
3A6948A
EN
Use Use
Use
to to
to
monitor monitor
monitor
and and
and
actively actively
actively
manage manage
manage
1K 1K
1K
󰘱uid 󰘱uid
󰘱uid
pressure pressure
pressure
or or
or
󰘱ow 󰘱ow
󰘱ow
rate, rate,
rate,
as as
as
well well
well
as as
as
track track
track
material material
material
use use
use
in in
in
permanently permanently
permanently
installed installed
installed
󰘱uid 󰘱uid
󰘱uid
supply supply
supply
systems. systems.
systems.
For For
For
professional professional
professional
use use
use
only. only.
only.
Important Important
Important
Safety Safety
Safety
Instructions Instructions
Instructions
Readallwarningsandinstructionsinthismanualandinthemeter,
regulator,andpowersupplymanualsbeforeusingtheequipment.
Save Save
Save
these these
these
instructions. instructions.
instructions.
SeetheG3000,S3000,G250meter
manual(308778)orCoriolismeter
manual(313599)for󰘱owmeter
maximumworkingpressure.
Seepage3formodelinformation,
includingapprovals.
PROVENQUALITY.LEADINGTECHNOLOGY.

Table of Contents

Questions and Answers

  • J
    Jon ZimmermanSep 8, 2025
    Why is the display readout faulty on my Graco Measuring Instruments?
    • A
      Adriana RobertsSep 8, 2025
      A faulty display readout on your Graco Measuring Instruments could be due to excessive static discharge or an ambient temperature that is too high. Consider replacing the ProControl 1KE Plus or lowering the ambient temperature.
  • O
    oayersSep 12, 2025
    Why is flow control over-driving to high flow rates in Graco Measuring Instruments?
    • D
      Dawn BurtonSep 12, 2025
      If the flow control is over-driving to high flow rates in your Graco Measuring Instruments, verify the pressure switch electrical connection for automatic operation. Check that the switch closes when the gun fluid solenoid is activated. For manual operation, verify the air flow switch electrical connection and check that the switch closes when the gun trigger is activated. The flow control may activate when the atomizing air is flowing without any fluid flow.
  • V
    victorgreenSep 12, 2025
    How to fix unstable flow with Coriolis meter in Graco Measuring Instruments?
    • J
      Juan BarrettSep 12, 2025
      If you're experiencing unstable flow with a Coriolis meter in your Graco Measuring Instruments, check for the presence of bubbles or sediment. Look for upwards settling of air bubbles and downwards settling of solids, such as metallics.
  • V
    Vickie AdamsSep 14, 2025
    Why does Coriolis meter show flow when no fluid is flowing on Graco Measuring Instruments?
    • A
      anthonyhuertaSep 15, 2025
      If the Coriolis meter shows flow when no fluid is flowing in your Graco Measuring Instruments, the low-flow cutoff may be set too low. Increase the low-flow cutoff to just above the highest false flow rate that was observed.
  • D
    Dennis NovakSep 17, 2025
    What causes regulator pilot to drive to high pressure in Graco Measuring Instruments?
    • C
      cheryl66Sep 17, 2025
      If the regulator pilot drives to high pressure in your Graco Measuring Instruments, it could be due to inadequate fluid supply in pressure control or flow control mode. Check the pressure and flow capabilities of the fluid supply.

Graco ProControl 1KE Plus Specifications

General IconGeneral
BrandGraco
ModelProControl 1KE Plus
CategoryControl Unit
LanguageEnglish

Related product manuals