To Next PageTo Next PageWhat to do if my Graco XM PFP Paint Sprayer fluid valve is leaking between the main and outlet housings?
If the fluid valve on your Graco Paint Sprayer is leaking between the main and outlet housings, the O-ring on the seat has likely failed. Replace both O-rings on that seat.
What to do if my Graco XM PFP fluid valve is leaking at the rod?
If the fluid valve is leaking at the rod of your Graco Paint Sprayer, it is likely due to loose or worn packings. Try tightening the packing nut. If the leak persists, replace the packings.
What to do if the Graco XM PFP Paint Sprayer does not start when the start button is pressed?
If your Graco Paint Sprayer fails to start when the start button is pressed: * Check for a faulty start switch or wire harness continuity; the switch is normally open circuit. * Check for a faulty stop switch or wiring harness continuity; the stop switch is normally closed circuit.
Why does my Graco XM PFP Paint Sprayer have a poor spray pattern?
A poor spray pattern in your Graco Paint Sprayer can be caused by: * Fluid pressure being too low. Increase the metering pump pressure. * Fluid temperature being too low. Increase the fluid temperature. * Spray tip being dirty or worn. Relieve pressure, then clean or replace the tip, following the gun manual instructions. * Mix manifold, mixer, swivel, gun, or hoses partially plugged or too restrictive. Inspect parts for cured material. Clean or replace, or use larger hoses and mixer.
Covers electric shock, fire, explosion hazards, and safe operating conditions.
Details skin injection, burn, and moving parts hazards for user safety.
Covers misuse, toxic fluids/fumes, splatter hazards, and PPE recommendations.
Covers keeping components separate and safe material changing procedures.
Details available system models, ratio ranges, and approvals.
Lists essential manuals for components and accessories.
Identifies key components and their locations in the front view of the sprayer.
Identifies key components and their locations in the back view of the sprayer.
Details fluid control assembly, power/heater controls, air controls, and user interface elements.
Covers site selection, unpacking, and system layout options.
Instructions for connecting modules, power, and air supply.
Guides connecting feed module lines, fluid hose bundles, and installing level sensors.
Instructions for connecting tank heat circulation hoses and priming heated systems.
Steps for powering on the machine and initial flushing if required.
Detailed procedure for loading material and priming the system.
Procedure for priming the flush pump for system cleaning.
Guidance on selecting ratio mode and setting the desired mix ratio.
Instructions for setting and adjusting material and hose temperatures.
Steps to ensure proper material mixing, priming, and temperature for spraying.
Procedure to flush mixed material from the system to prevent curing.
Steps to park metering pump rods to prevent material hardening.
Essential steps to safely relieve pressure before servicing or stopping the equipment.
Procedure to test and calibrate pumps for accurate ratio by weight.
Tests for dispensing volumes, verifying ratios, and detecting valve leaks.
Procedure to minimize waste when emptying and flushing the entire system.
Details on USB logs, setup, and the download procedure.
Covers adjusting packing nuts, filters, seals, and battery replacement.
Instructions for thoroughly cleaning the sprayer system.
General tips for setup, grounding, air supply, calibration, and motor icing.
Information on alarms, module diagnostics, and troubleshooting common issues.
Explains UI layout, changing settings, and alarm display.
Details on configuring system settings like ratio, temperature, and USB options.
Screens for running pumps, spraying, parking, and performing tests.
Screens for viewing alarms, logs, totals, and maintenance schedules.
Explains alarm display, levels, and provides a code interpretation key.
Details possible alarms by mode and troubleshooting steps for specific alarm codes.
Lists detailed technical specifications for the XM PFP sprayer.
Information regarding Graco's standard warranty terms and conditions.
General| Brand | Graco |
|---|---|
| Model | XM PFP |
| Category | Paint Sprayer |
| Language | English |
