What causes relief valve leaks back to supply, opens too soon, or will not close in Graco Airbrushes?
If the relief valve in your Graco Airbrushes leaks back to the supply, opens too soon, or will not close, it is likely that the relief valve is dirty or damaged. Replace the over pressure relief valve.
What to do if relief valve leaks on Graco Paint Sprayer?
If the relief valve on your Graco Paint Sprayer leaks back to the supply, opens too soon, or won't close, it indicates that the relief valve is either dirty or damaged. Replace the over pressure relief valve.
Why does my Graco Paint Sprayer run erratically?
If your Graco Paint Sprayer system speeds up or runs erratically, it could be due to empty fluid containers, so check them often and keep them filled. Another cause might be air in the fluid lines; purge the lines and check the connections. Also, worn or damaged displacement pump parts can cause this issue; in that case, repair the pump.
What to do if resin output pressure drops on both strokes of Graco XP70 Paint Sprayer?
If your Graco Paint Sprayer pump operates, but the resin output pressure drops on both strokes, it could be due to a hardener output restriction. Clean and unplug the hardener side, and open the manifold restrictor. Alternatively, the fluid supply might be low, so refill or change the container.
What to do if hardener output pressure drops on both strokes of Graco Paint Sprayer?
If your Graco Paint Sprayer pump operates, but the hardener output pressure drops on both strokes, it could be due to a resin output restriction. Clean and unplug the resin side. Alternatively, the fluid supply might be low, so refill or change the container.
What causes fluid leak under packing nut of Graco Airbrushes?
A fluid leak under the packing nut of your Graco Airbrushes may be due to the packing cartridge o-ring. Replace the cartridge o-ring.
What causes pressure and flow surges on upstroke with Graco Airbrushes?
Pressure and flow surges on the upstroke with Graco Airbrushes can occur if the feed pressure is too high. Every 1 psi of feed pressure adds 2 psi during the upstroke. Reduce the feed pressure to resolve this issue.
What causes fluid leak in packing nut of Graco Airbrushes?
A fluid leak in the packing nut of your Graco Airbrushes is often caused by a loose packing nut or worn throat packings. Try tightening the packing nut and replacing the throat packings.
How to fix fluid leak under packing nut of Graco Paint Sprayer?
If you observe a fluid leak under the packing nut of your Graco Paint Sprayer, it's likely due to the packing cartridge o-ring. You'll need to replace the o-ring.
What to do if hardener output pressure drops on downstroke of Graco Paint Sprayer?
If your Graco Paint Sprayer pump operates, but the hardener output pressure drops on the downstroke, it could be due to a dirty, worn, or damaged hardener pump intake valve. In this case, you should clean and repair the pump.
Covers risks of electric shock, fire, and explosion.
Details risks like skin injection, moving parts, and toxic exposure.
Addresses improper use and necessary personal protective equipment.
Discusses conditions affecting isocyanates and safe handling.
Details mix ratios and specifications for XP models.
Comprehensive table of XP pump packages with mix ratios and specifications.
Essential information on grounding for safety and static discharge prevention.
Detailed instructions for connecting electrical power to the system.
Critical procedure for safely relieving system pressure before servicing.
Steps to prime the system with A and B fluids before operation.
Specific priming steps for XP and XP-h systems.
Procedures for recirculating material and heating fluid.
Steps for initiating and performing the spraying process.
Procedure for flushing mixed material from the system.
Procedure for emptying and flushing the complete system.
Steps to empty the system of material.
Steps to flush the system with solvent.
Instructions for safely parking and shutting down the system.
Daily tests to verify system operation, mixing, and integration.
Troubleshooting common startup and erratic operation problems.
Guide to diagnose pump malfunctions using fluid gauges.
General| Fluid Output | 2.0 gpm (7.6 lpm) |
|---|---|
| Fluid Delivery | 2.0 gpm (7.6 lpm) |
| Maximum Fluid Working Pressure | 7250 psi (500 bar) |
| Maximum Air Input Pressure | 100 psi (7 bar) |
| Fluid Outlet Size | 3/8 in npsm(m) |
| Wetted Parts | Stainless Steel, PTFE, UHMWPE |
| Maximum Pressure | 7250 psi (500 bar, 50 MPa) |
| Hose Length | 50 ft |
To Next Page
