GRAPHTEC CE LITE-50 - Ordinary Care and Cleaning

2-14
Chapter 2 Basic Operations
2.8 Ordinary Care
&RQGXFWRUGLQDU\FDUHZKLOHEHLQJFDUHIXORIWKHLWHPVOLVWHGEHORZ

5HIUDLQIURPOXEULFDWLQJWKHPHFKDQLFDOVHFWLRQ

7RFOHDQWKHPDLQXQLWZLSHWKHXQLWZLWKHLWKHUDGU\FORWKRUDFORWKVRDNHGLQDGLOXWHGQHXWUDOGHWHUJHQW
5HIUDLQIURPXVLQJVXEVWDQFHVVXFKDVSDLQWWKLQQHUEHQ]HQHRUDOFRKROHWFDVWKHVHZLOOGDPDJHWKH
surface.
Media Sensor
Push Roller
Cutting Mat

IIWKHFXWWLQJPDWLVGLUW\FOHDQLWE\ZLSLQJLVZLWKDGU\FORWK
IIWKHFXWWLQJPDWLVYHU\GLUW\ZLSHLWZLWKDFORWKPRLVWHQHGZLWK
alcohol or a diluted neutral detergent.

'XVWRUGLUWHWFDWWDFKLQJWRWKHVHQVRUXQLWZKLFKVFDQVWKHPHGLDRUWKH
roller unit that transports the media can cause the device to malfunction.
5HJXODUO\ZLSHWKHVHFRPSRQHQWVZLWKDFORWKRUFRWWRQVZDEVPRLVWHQHG
with alcohol or a diluted neutral detergent.
*$EVROXWHO\UHIUDLQIURPXVLQJEHQ]HQHSDLQWWKLQQHUHWF

IIWKH<UDLOVOLGLQJVXUIDFHKDVEHFRPHGLUW\JHQWO\ZLSHRIIWKHGLUWZLWKDFOHDQGU\FORWK
/XEULFDQWVHHSVRXWRQWRWKHVOLGLQJVXUIDFH$YRLGIRUFHIXOO\ZLSLQJWKLVRII
Storage Method
%HFDUHIXORIWKHIROORZLQJLWHPVIRUVWRUDJHZKHQWKHGHYLFHZLOOQRWEHXVHG

%HVXUHWRUHPRYHWKHWRROIURPWKHWRROKROGHUZKHQVWRULQJWKHGHYLFH

3UHYHQWGXVWIURPDFFXPXODWLQJE\FRYHULQJWKHPDLQXQLWZLWKDFRYHUFORWKFRYHU

5HIUDLQIURPVWRULQJWKHGHYLFHLQDORFDWLRQH[SRVHGWRGLUHFWVXQOLJKWRUVXEMHFWWRKLJKWHPSHUDWXUHVDQG
humidity.

Raise the media set levers and place the push rollers in their unlocked state for storage.
Cleaning the Cutter Pen
0HGLDVFUDSVHWFDWWDFKHGWRWKHWLSRIWKHFXWWHUEODGHZLOOORZHUWKHTXDOLW\RIWKHFXWV
5HJXODUO\FOHDQWKHFXWWHUSHQWRUHPRYHDQ\PHGLDVFUDSVHWF
CAUTION

Be very careful when handling the cutter blade to avoid cutting your hands, etc.

Clean the tip of the cutter blade with air or a soft material. Using a stiff material can cause the blade to chip or break.
Blade Tip Cap
Blade Tip
Cap Jig
Cutter Blade
1. Align the red line on the cutter pen with "0" to place it in a state
ZKHUHWKHEODGHLVQRWSURWUXGLQJ
2. 7XUQWKH%ODGH7LS&DSWRFRXQWHUFORFNZLVHWRUHPRYHLWE\XVLQJ
WKH%ODGH7LS&DS-LJ
$WWDFKWKH%ODGH7LS&DS-LJWRWKH%ODGH7LS&DSDQGWKHQ
UHPRYHWKH%ODGH7LS&DSZKLOHKROGLQJWKHQXPEHUSDUWRI
cutter pen as shown in the picture.
3. &OHDQWKHUHPRYHGEODGHWLSFDSDQGFXWWHUEODGHZLWKDLURUD
soft material.
4. $WWDFKWKH%ODGH7LS&DSWRWKH&XWWHUSHQDQGWKHQPDQXDOO\WXUQWKH%ODGH7LS&DSFORFNZLVHWRLQVWDOOLW
6HFXUHO\WLJKWHQWKH%ODGH7LS&DSE\XVLQJWKH%ODGH7LS&DS-LJ