Gree GFH09K3FI - Page 33

30
U-Match Series DC
Inverter Service Manual
DPOUSPM
(1). Mode 1 (LCD displays 00)
(2). Mode 2 (LCD displays 01)
Note:
ķ
Mode 1: Compressor electric heating belt starts when outdoor ambient temperature is below 35°C and
stops when outdoor ambient temperature is above 37°C. When outdoor ambient temperature is within
35°C~ 37°C, the belt will keep its previous operation state.
ĸ
Mode 1: Compressor electric heating belt starts when outdoor ambient temperature is below -2°C and stops
when outdoor ambient temperature is above 0°C. When outdoor ambient temperature is within -2°C~0°C,
the belt will keep its previous operation state.
4.9.7 Selecting low-power consumption mode
8QGHUGHEXJJLQJVWDWHSUHVV0RGHEXWWRQWRDGMXVWWR³´LQWHPSHUDWXUHGLVSOD\LQJ]RQH7LPHU]RQH
GLVSOD\VVHWWLQJVWDWHDQGSUHVVŸRUźEXWWRQWRDGMXVW7KHUHDUHVHOHFWLRQV
(1). With low-power consumption mode (LCD displays 00)
(2). Without low-power consumption mode (LCD displays 01)
4.9.8 Selecting door control function
8QGHUGHEXJJLQJVWDWHSUHVV0RGHEXWWRQWRDGMXVWWR³´LQWHPSHUDWXUHGLVSOD\LQJ]RQH7LPHU]RQH
GLVSOD\VVHWWLQJVWDWHDQGSUHVVŸRUźEXWWRQWRDGMXVW7KHUHDUHVHOHFWLRQV
(1). Without door control function (LCD displays 00)
(2). With door control function (LCD displays 01)
4.9.9 Selecting human sensitive function
8QGHUGHEXJJLQJVWDWHSUHVV0RGHEXWWRQWRDGMXVWWR³´LQWHPSHUDWXUHGLVSOD\LQJ]RQH7LPHU]RQH
GLVSOD\VVHWWLQJVWDWHDQGSUHVVŸRUźEXWWRQWRDGMXVW7KHUHDUHVHOHFWLRQV
(1). Without human sensitive function (LCD displays 00)
(2). With human sensitive function (LCD displays 00)
4.9.10 Selecting long-distance monitoring or centralized controller
8QGHUGHEXJJLQJVWDWHSUHVV0RGHEXWWRQWRDGMXVWWR³´LQWHPSHUDWXUHGLVSOD\LQJ]RQH7LPHU]RQH
GLVSOD\VVHWWLQJVWDWHDQGSUHVVŸRUźEXWWRQWRDGMXVW7KHUHDUHVHOHFWLRQV
(1). Centralized controller (LCD displays 00)
(2). Long-distance monitoring (LCD displays 01)
4.9.11 Selecting fan mode of indoor fan motor
8QGHUGHEXJJLQJVWDWHSUHVV0RGHEXWWRQWRDGMXVWWR³´LQWHPSHUDWXUHGLVSOD\LQJ]RQH7LPHU]RQH
GLVSOD\VVHWWLQJVWDWHDQGSUHVVŸRUźEXWWRQWRDGMXVW7KHUHDUHVHOHFWLRQV
(1). P3 (LCD displays 03)
(2). P4 (LCD displays 04)
(3). P5 (LCD displays 05)
(4). P6 (LCD displays 06)
(5). P7 (LCD displays 07)
Note: You can select P03, P04, P05, P06, P07 in fan mode of indoor fan motor, which means different fan
mode combinations are corresponding to different static pressure. Ex-factory defaulted mode is P05. You can
set the mode through wired controller. S01, S02, S03……S12, S13 means the rotation speed of indoor unit is
from low to high.
Table 2-4-2 Combination relationship of P03, P04, P05, P06, P07
Static
pressure
selection
Super high
speed
High speed
Medium
high speed
Medium
speed
Medium
low speed
Low speed
Quiet
R1 speed
Quiet
R2 speed
Quiet
R13 speed
P03 S09 S08 S07 S06 S05 S04 S03 S02 S01
P04 S10 S09 S08 S07 S06 S05 S04 S03 S02
P05 S11 S10 S09 S08 S07 S06 S05 S04 S03
P06 S12 S11 S10 S09 S08 S07 S06 S05 S04
P07 S13 S12 S11 S10 S09 S08 S07 S06 S05
4.9.12 Selecting compensation of temperature sensor at air return
8QGHUGHEXJJLQJVWDWHSUHVV0RGHEXWWRQWRDGMXVWWR³´LQWHPSHUDWXUHGLVSOD\LQJ]RQH7LPHU]RQH
GLVSOD\VVHWWLQJVWDWHDQGSUHVVŸRUźEXWWRQWRDGMXVW7KHUHDUHVHOHFWLRQV
(1). Compensate 0°C (LCD displays 00)
(2). Compensate 1°C (LCD displays 01)
(3). Compensate 2°C (LCD displays 02)