GreenWorks GDC40 User Manual (English)

Other manuals for GreenWorks GDC40

Manual41 pages

Operator's Manual180 pages

Questions and Answers:

W
warrenchandlerAug 13, 2025
How to fix GreenWorks GDC40 Pressure Washer that has low pressure?
- K
  Kevin ScottAug 14, 2025
  If your GreenWorks Pressure Washer isn't reaching high pressure, several factors could be at play. Start by checking the garden hose diameter; it should be 1” (25 mm) or 5/8” (16 mm). Ensure the garden hose isn't blocked and that the water supply is fully open. Verify the nozzle is correctly installed on the spray wand. Lastly, inspect the water inlet filter and clean it in warm water if it's blocked.
A
Ashley CisnerosAug 17, 2025
What to do if my GreenWorks GDC40 Pressure Washer motor won't start?
- T
  Tara ReedAug 17, 2025
  If the motor on your GreenWorks Pressure Washer isn't starting, first ensure the power switch is in the “ON” ( | ) position. Next, confirm the battery pack is properly installed. Finally, make sure you are pulling the gun trigger after turning the power switch on.
C
carl60Aug 21, 2025
Why is my GreenWorks GDC40 Pressure Washer motor buzzing but not starting?
- J
  Jennifer WhiteAug 21, 2025
  If your GreenWorks Pressure Washer motor buzzes but doesn't start, it could be due to a few reasons. A discharged battery pack needs to be charged. If there's remaining pressure in the system, stop the machine, pull the gun trigger to release the pressure, and then restart the machine. There also might be remaining friction in components. To resolve that: disconnect the water supply, turn the machine on for 2 or 3 seconds, and repeat several times.
D
Derek ValenciaAug 25, 2025
Why does the output pressure of my GreenWorks Pressure Washer fluctuate?
- A
  Albert MartinezAug 26, 2025
  The fluctuating output pressure of your GreenWorks Pressure Washer can be due to several reasons: insufficient water supply (fully open the water supply and ensure the garden hose isn't blocked), air in the pump (ensure hoses and fittings are secure, turn off the machine, and pull the gun trigger until a stable water flow emerges), a clogged water inlet filter (clean it in warm water), a depleted battery pack (charge it), or calcified components (operate distilled vinegar through the detergent tank).
M
Martin JohnsonAug 28, 2025
What to do if my GreenWorks GDC40 doesn't have high pressure?
- D
  Debra HillAug 29, 2025
  If your GreenWorks Pressure Washer isn't producing high pressure, check the following: ensure you are using a 1” (25 mm) or 5/8” (16 mm) garden hose, verify that the garden hose isn't blocked, fully open the water supply, ensure the nozzle is correctly installed onto the spray wand, and clean the water inlet filter in warm water.
D
Derrick JenkinsSep 1, 2025
Why does my GreenWorks GDC40 Pressure Washer motor buzz but not start?
- M
  Misty StewartSep 1, 2025
  If your GreenWorks Pressure Washer motor buzzes but the machine won't start, it could be due to a depleted battery pack (charge it) or remaining pressure in the system (stop the machine, pull the gun trigger to release pressure, then restart the machine). If you haven't used the machine for a long time, speak to a person of an approved service center. If there is remaining friction in components and you can hear a hum, disconnect the water supply, turn the machine on for 2 or 3 seconds, and repeat this step several times.
J
Joseph GilbertSep 5, 2025
Why does my GreenWorks GDC40 Pressure Washer have inconsistent pressure?
- M
  maxwell01Sep 5, 2025
  Inconsistent pressure in your GreenWorks Pressure Washer can stem from several causes. First, ensure your water supply is fully open and the garden hose isn't blocked. Air in the pump can also cause this; check hoses and fittings, then turn off the machine and pull the trigger until a steady water flow emerges. A clogged water inlet filter requires cleaning in warm water. A depleted battery pack needs charging. Finally, calcification in the gun, hose, or nozzle may require running distilled vinegar through the detergent tank.
E
Emily MendezSep 9, 2025
Why is there no water coming from my GreenWorks Pressure Washer?
- K
  Kathleen JonesSep 9, 2025
  If no water is coming from your GreenWorks Pressure Washer, first ensure that the water supply is turned on and that the garden hose is free from any blockages.

GreenWorks GDC40 Specifications

General

Power Source	Battery
Hose Length	20 ft
Max Pressure	70 bar
Flow Rate	1.1 GPM
Weight (without battery)	6.4 kg
Maximum Pressure	70 bar
Water Flow	1.1 GPM
Weight	8.6 lbs (without battery)