GreenWorks GPW 2002 - User Manual

Questions and Answers

S
Steven SmallAug 16, 2025
How to fix a GreenWorks Pressure Washer when the motor will not start?
- J
  james02Aug 16, 2025
  If your GreenWorks Pressure Washer motor won't start, first ensure the On/Off switch is in the “ON” ( | ) position. Then, check if the power cord is properly plugged in. If it is, try a different electrical outlet to rule out inadequate power supply. Also, allow the unit to cool and restart it if the pressure washer circuit breaker tripped. Finally, with the power switch ON, push in on the gun trigger to engage the AUTO ON switch.
S
Shannon WilliamsAug 18, 2025
Why does my GreenWorks GPW 2002 Pressure Washer motor buzz but fails to run?
- A
  April LongAug 18, 2025
  If the motor of your GreenWorks Pressure Washer buzzes but fails to run, verify that only the pressure washer is running on the circuit. Turn the unit “OFF”, squeeze the trigger on the spray wand to release any residual pressure, then turn the unit "ON". Unplug any extension cords and plug the unit directly into the outlet. If the pressure washer hasn't been used for a long time, call the Toll-Free Helpline. In case of residual friction among components, disconnect the water supply and power ON for 2 to 3 seconds, repeating a couple of times or until the motor starts.
P
Phillip MontgomeryAug 21, 2025
How to fix a GreenWorks GPW 2002 when the detergent is not coming out?
- K
  Kevin CrossAug 21, 2025
  If detergent isn't coming out of your GreenWorks Pressure Washer, dilute the detergent if it's too thick. Run warm water through the filter on the detergent suction tube to remove any build-up. Remove any obstruction or replace the detergent suction tube if it's damaged or clogged. Blow out or remove debris from the spray tip with a fine needle if it's obstructed.
P
peter16Aug 25, 2025
Why is soap not coming out or coming out at low pressure from my GreenWorks pressure washer?
- D
  Daniel ParkerAug 25, 2025
  If soap does not come out or comes out at low pressure from your GreenWorks pressure washer, install the 75 degree, black, soap tip in wand. If the soap tank may be plugged with debris or thick soap, empty soap from tank, clean out using vinegar and water.
K
klopezAug 27, 2025
What to do if my GreenWorks GPW 2002 Pressure Washer does not reach high pressure?
- N
  Nicholas BanksAug 28, 2025
  If your GreenWorks Pressure Washer isn't reaching high pressure, replace the garden hose with a 1” (25 mm) or 5/8” (16 mm) garden hose. Check the garden hose for kinks, leaks, and blockage to ensure the water supply isn't restricted. Fully open the water source to provide enough water supply. Ensure the pressure tip is correctly installed on the wand assembly. Also, remove and rinse the water inlet filter in warm water if it's clogged.
R
Robert JensenAug 30, 2025
Why is the pump on my GreenWorks Pressure Washer so noisy?
- A
  Alexander MontoyaAug 30, 2025
  If your GreenWorks Pressure Washer pump is noisy, check that the hoses and fittings are airtight, then turn off the machine and purge the pump by squeezing the trigger gun until a steady flow of water emerges through the spray tip. Also, remove the water filter and rinse it in warm water to ensure it is not clogged.
C
Cindy VargasSep 2, 2025
What to do if my GreenWorks GPW 2002 Pressure Washer has no water coming out?
- S
  Suzanne SmithSep 2, 2025
  If there's no water coming out of your GreenWorks Pressure Washer, first, make sure the water supply is turned ON. If that's not the issue, check the garden hose for any kinks and remove them.
S
Sandra HendersonSep 5, 2025
Why is the garden hose connection leaking on my GreenWorks GPW 2002?
- A
  alison35Sep 5, 2025
  If your garden hose connection is leaking on your GreenWorks Pressure Washer, tighten the connection. If the leak persists, insert a new washer, as the existing one may be missing or worn.
E
erica77Sep 9, 2025
Why is water leaking from the pump of my GreenWorks Pressure Washer?
- V
  Vincent CoxSep 9, 2025
  If water leaks from the pump of your GreenWorks Pressure Washer, check that all fittings are tight. If the water continues to leak, call the Toll-Free Helpline because the water seals are damaged or worn.
R
Robert TurnerSep 12, 2025
Why is oil dripping from my GreenWorks GPW 2002?
- D
  david39Sep 12, 2025
  If oil is dripping from your GreenWorks Pressure Washer, call the Toll-Free Helpline because the oil seals are damaged or worn.

Summary

Product Specification

Important Safety Instructions

Specific Safety Rules

Symbols

Service

Electrical Connection

Know Your Pressure Washer

Packing List

Assembly

Assembling the Gun Holder

Insert the gun holder into the gun holders slot until it locks into place.

Connecting High Pressure Hose to Trigger Handle

Align hose with trigger handle, push up, and secure hose lock clockwise.

Assembling the Spray Wand

Push spray wand into trigger handle, rotate to secure, and pull to confirm.

Connecting the Garden Hose

Observe local regulations. Ensure 10ft hose. Run water to clean debris. Inspect/clean water intake screen.

Operation

Applications

Clean boats, cars, trucks, outdoor furniture, grills, siding, driveways, patios, and decks.

Detergent Adding and Use

Use approved detergents. Prepare solution as instructed on bottle. Use black soap tip for soap application.

Starting and Stopping the Pressure Washer

Connect hose, bleed air, plug in, turn on. Release trigger to stop. Features auto start/stop.

Using the Spray Tips

Select spray tip (Green, White, Black, Turbo) based on application. Attach securely to wand.

Using the Spray Wand Trigger

Hold handle with both hands. Pull trigger to operate. Release to stop. Use lock-out for safety.

Operating the Pressure Washer

Apply detergent with soap tip, then rinse with 25° tip. Maintain proper distance from surface.

Moving the Pressure Washer

Turn off, release pressure, tilt and roll on wheels to desired position.

Maintenance

Spray Tip Maintenance

Check for clogged spray tips causing pulsing pressure. Clean with tool and flush with water.

Quick Winterizing Procedure

Disconnect water, run pump briefly, store in non-freezing room. Drain gun.

Shutting Down and Cleaning Up

Flush detergent system, disconnect hose, release pressure, turn off, unplug, engage lock.

Taking a Break

Engage safety lock, turn to OFF, unplug power cord.

Troubleshooting

Warranty

Exploded View

Parts List

GreenWorks GPW 2002 Specifications

General

Power Source	Electric
Maximum Pressure	2000 PSI
Water Flow	1.2 GPM
Motor	13 Amp
Power Cord Length	35 feet
Hose Length	20 feet
Nozzles Included	3 (0°, 25°, 40°)
Warranty	3-year tool warranty