7
6.2 Type key
* Only pumps up to and including 0.37 kW and only single-phase pumps
Example: DMX 115 - 3 B PP /E /T -X -E 1 QQ X E0
Type range Motor variant
Maximum flow [l/h] E0 PTC motor for frequency control
Maximum counter-pressure [bar] E1
Motor type EEx de C T3, 3 x 400 V,
50 Hz (only DMX-B or DMX-AT)
Control variant E2
Motor type EEx de C T4, 3 x 400 V,
50 Hz (only DMX-B or DMX-AT)
B Standard - manual control Mains plug
AR* Analog/pulse control F EU (Schuko)
AT0 Prepared for servomotor B USA, Canada
AT3
Servomotor, 1 x 230 V, 50/60 Hz supply,
4-20 mA control
I Australia, New Zealand, Taiwan
E Switzerland
AT5
Servomotor, 1 x 115 V, 50/60 Hz supply,
4-20 mA control
X No plug
Connection, suction/discharge
AT8
Servomotor, 1 x 230 V, 50/60 Hz supply,
1 kΩ potentiometer control
4 Tube 6/9 mm
B1
Tube 6/12 mm/
cementing d. 12 mm
AT9
Servomotor, 1 x 115 V, 50/60 Hz supply,
1 kΩ potentiometer control
6 Tube 9/12 mm
B2
Tube 13/20 mm/
cementing d. 25 mm
Dosing head variant Q Tube 19/27 mm and 25/34 mm
PP Polypropylene R Tube 1/4" / 3/8”
PV PVDF (polyvinylidene fluoride) S Tube 3/8" / 1/2”
PVC Polyvinyl chloride C5 Hose clamp 1/2"
SS Stainless steel, DIN 1.4401 A Threaded Rp 1/4
PV-R PVDF + integrated relief valve A1 Threaded Rp 3/4
PVC-R PVC + integrated relief valve V Threaded 1/4" NPT, female
PP-L PP + integrated diaphragm leakage detection A9 Threaded 1/2" NPT, male
PV-L PVDF + integrated diaphragm leakage detection A3 Threaded 3/4" NPT, female
PVC-L PVC + integrated diaphragm leakage detection A7 Threaded 3/4" NPT, male
SS-L SS + integrated diaphragm leakage detection B3 Welding, diameter 16 mm
PV-RL
PVDF + integrated relief valve and
diaphragm leakage detection
B4 Welding, diameter 25 mm
Valve type
PVC-RL
PVC + integrated relief valve and
diaphragm leakage detection
1 Standard valve
3
Spring-loaded
0.05 bar suction opening pressure
0.8 bar discharge opening pressure
Gasket material
EEPDM 4
Spring-loaded, discharge side only
0.8 bar opening pressure
VFKM 5 Valve for abrasive media
T PTFE Supply voltage
Valve ball material G 1 x 230 V, 50/60 Hz
GGlass H 1 x 120 V, 50/60 Hz
T PTFE
E
3 x 230/400 V, 50/60 Hz
or 3 x 440/480 V, 60 Hz
SS Stainless steel, DIN 1.4401
Control panel position F Without motor, NEMA flange (US)
F Front-mounted (opposite to the dosing head) 0 Without motor, IEC flange
S
Side-mounted (same side as the stroke-length adjustment
knob)
Sx
Side-mounted (side opposite to the stroke-length adjustment
knob)
W Wall-mounted
X No control panel
To Next Page
Loading...
