GTO 2000XLS User Manual

Installation Manual for the
SINGLE Gate Operator System
PROFESSIONAL INSTALLATION RECOMMENDED!
WARNING!
This equipment is similar to other gate or door equipment and meets or exceeds
Underwriters Laboratory Standard 325 (UL 325). However, gate equipment has
hazards associated with its use and therefore by installing this product the installer
and user accept full responsibility for following and noting the installation and
safety instructions. Failure to follow installation and safety instructions can result
in hazards developing due to improper assembly. You agree to properly install this
product and that if you fail to do so Gates That Open, LLC, (“GTO”) shall in no event
be liable for direct, indirect, incidental, special or consequential damages or loss of
prots whether based in contract tort or any other legal theory during the course
of the warranty or at any time thereafter. The installer and/or user agree to assume
responsibility for all liability and use of this product releasing Gates That Open, LLC,
from any and all liability. If you are not in agreement with this disclaimer or do not
feel capable of properly following all installation and safety instructions you may
return this product for full replacement value.
READ ALL INSTRUCTIONS CAREFULLY AND COMPLETELY before attempting to
install and use this automatic gate operator. This gate operator produces a high level
of force. Stay clear of the unit while it is operating and exercise caution at all times.
All automatic gate operators are intended for use on vehicular gates only.
This product meets and exceeds the requirements of UL 325, the standard which
regulates gate operator safety, as established and made eective March 1, 2000, by
Underwriters Laboratories Inc.
For more information on the GTO/ACCESS SYSTEMS full line of automatic gate
operators and access controls visit our website at www.gtoaccess.com.
©2011 Gates That Open, LLC Printed in China for Gates That Open, LLC. R4717 02.07.12
, LLC
®
2000XLS
2000XLS
PROFESSIONAL RESIDENTIAL
ACCESS
SYSTEMS

GTO 2000XLS Specifications

General

Brand	GTO
Model	2000XLS
Category	Gate Opener
Language	English

Summary

Please Read This First

Before You Begin Installation

Key preliminary information and instructions before starting the gate operator installation.

Important Safety Instructions

Manual Gate Operation

Guidance on how to manually open and close the gate when the operator is disconnected.

Disconnecting the Operator

Procedure for safely disconnecting the gate operator from the gate.

Consumer Safety Precautions

Safety guidelines and warnings specifically for the end-user of the gate operator.

Before Installation Checklist

Essential checks and verifications to perform before beginning the gate operator installation.

Installation Safety Guidelines

Critical safety instructions to follow during the installation process of the gate operator.

Post-Installation Safety

Safety measures and warnings to be aware of after the gate operator has been installed.

Gate Safety Precautions

Specific safety precautions required for gates when installing an automatic operator.

Entrapment Protection

Details on secondary means to protect against entrapment, as per UL 325.

Entrapment Alarm Function

Explanation of the entrapment alarm feature and its behavior.

Technical Specifications

Drive System Details

Specifications related to the operator's drive mechanism, motor, and arm stroke.

Power System Overview

Control Board Features

Before You Begin

Determine Battery Charging Method

Guidance on choosing between transformer or solar panel for battery charging.

Check Gate Swing Direction

Gate Preparation

Gate Grounding Procedure

Instructions for properly grounding the gate operator system to reduce lightning risk.

Install the Operator

Step 1: Post Bracket Alignment

Step 2: Attach Post Bracket to Opener

Step 3: Attach Gate Bracket

Step 4: Leveling and Securing Brackets

Step 5: Align Post Pivot Bracket

Step 6: Check Clearance and Leverage

Step 7: Secure Brackets

Step 8: Mark and Drill Holes

Step 9: Mount Post Brackets

Step 10: Mount Gate Bracket

Attach Operator Arm

Connect Operator Power Cable

Connect the Transformer

Lay Low Voltage Wire

Connect Low Voltage Wire

Stripping and connecting low voltage wire ends to the control board terminals.

Connect Transformer to Wire

Connecting the transformer wires to the low voltage wire ends.

Set the CLOSED Position Limit for PULL-TO-OPEN Installation

Step 1: Ensure Gate is Open

Step 2: Prepare Limit Setting

Step 3: Set Limit Button

Step 4: Verify Open Limit

Adjust the Stall Force Setting

Set Auto-Close Time

Personal Transmitter Setting

Push-To-Open Installation Information

Install Operator for Push-To-Open

Specific instructions for installing the operator in a push-to-open configuration.

Step 1: Remove Push-To-Open Jumper

Removing the jumper on the control board to enable push-to-open functionality.

Step 2: Set Open Position Limit

Setting the open position limit for the gate operator in push-to-open mode.

Solar Panel Instructions

Connecting Accessories

Step 1-3: General Connection

Accessory Input Terminals

Description of accessory input terminals on the control board and their functions.

Troubleshooting Guide

Diagnostic Indicators

Interpreting visual and audible indicators for troubleshooting gate opener issues.

Gate and Opener Maintenance

Repair Service