Labels
7
Training of Authorized Persons to correctly erect, disassemble, inspect, maintain, store, and use equipment
must be provided by a Competent Person. Training must include the ability to recognize fall hazards, minimize
the likelihood of fall hazards, and the correct use of personal fall arrest systems.
NEVER use fall protection equipment of any kind to hang, lift, support, or hoist tools or equipment, unless
explicitly certified for such use.
Equipment subjected to forces of fall arrest must immediately be removed from use.
Age, fitness, and health conditions can seriously affect the worker should a fall occur. Consult a doctor if there
is any reason to doubt a user’s ability to withstand and safely absorb fall arrest forces or perform set-up of
equipment. Pregnant women and minors must not use this equipment.
Physical harm may still occur even if fall safety equipment functions correctly. Sustained post-fall suspension
may result in serious injury or death. Use trauma relief straps to reduce the effects of suspension trauma.
85037 (Rev. O)
Guardian 607 East Sam Houston Parkway South, Suite 800 Pasadena, TX 77503 ph: +1(800) 466 6385 customer.service@gaurdianfall.com
7
guardianfall.com
Temper Anchor
Material: Zinc-plated steel
Capacity range (including all equipment): 130-420 lb.
Avoid contact with all hazards, including, but not
limited to, electricity, chemicals, and heat.
If used with HLL, HLL must be parallel with long side of anchor plate.
MAXIMUM 1 connection per Temper Anchor.
IMMEDIATELY remove from use if exposed to forces of fall arrest.
User must inspect prior
to each use. Competent
Person must inspect at
least every 12 months.
Competent Person to
initial year and month
of inspection
Connections must be selected and deemed compatible with Temper Anchor
by a Competent Person. Refer to instructions for proper connection methods.
May be used in multiple installation applications.
Always use new fasteners for each installation.
Prior to use, read and understand all manufacturer’s instructions
provided with equipment at time of shipment from manufacturer.
!
WARNING
Date of first use:
_____ / _____
Minimum substrate thickness requirements:
Wood: 3/4”. Metal: 20g.
Refer to instructions for proper installation
methods and fastener requirements.
90040 (Rev. I)
Made in China
Temper Anchor MUST lie flush against substrate.
Rango de Capacidades (incluyendo todos los equipos): 130-420 lb.
Evite el contacto con todos los riesgos, incluyendo, pero no limitado a,
la electricidad, los productos químicos, y el calor.
Si se usa con HLL, HLL debe estar paralelo al lado largo de la placa de anclaje.
MÁXIMO 1 contacto por Temper Anchor.
Retirar INMEDIATAMENTE del uso de la fuerza si se expone a caer arresto.
El usuario debe inspeccionar
cada archivo andes de usar.
Persona Competente debe
inspeccionar por lo menos
cada 12 meses. Persona
Competente a mes y el
año inicial de la inspección.
Conexiones deben ser seleccionados y considere compatible con Temper
Anchor por una Persona Competente. Consulte las instrucciones de los
métodos de conexión adecuados.
Se puede utilizar en aplicaciones de sistemas múltiples.
Siempre use fijaciones nuevas para instalar cada archivo.
Andes del uso, lea las instrucciones del fabricante y entendido todas
provisto de equipo al momento del envío desde el fabricante.
!
ADVERTENCIA
Fecha de primer uso:
_____ / _____
Requisitos mínimos del espersor del sustrato:
Madera: 3/4”. Metal: 20g.
Consulte las instrucciones para la instalación de
métodos apropiados y los requisitos de sujeción.
90040 (Rev. I)
Hecho en China
Temper Anchor DEBE ras de sustrato se une.
5,000 lb. MBS (minimum breaking strength).
Minimum service temperature: -30° F.
5,000 lb. MBS (resistencia mínima a la ruptura).
Temperatura mínima de servicio: -30° F.
DO NOT side-load (see instructions).
NO cargue de lado (vea las instrucciones).
Part #:
00455
guardianfall.com
Material: Acero Zincado
Fecha de
Fabricación:
# de Parte:
00455
# de lote:
Número de serie:
:
OSHA 1910.140, OSHA 1926.502
ANSI/ASSP Z359.18, A10.32
DOM:
Lot:
Serial:
Temper Anchor
OSHA 1910.140, OSHA 1926.502
ANSI/ASSP Z359.18, A10.32
To Previous Page