TX100 USB 2 6T7639a
1. General information about the Tebis installations and their configuration ........................................................................ 3
1.1 The various product types ........................................................................................................................................... 3
1.2 The different installation types..................................................................................................................................... 3
1.3 General information about the configuration and the management of the Tebis installations..................................... 4
1.4 Presentation of the configuration tool TX100 .............................................................................................................. 5
1.4.1 General view....................................................................................................................................................... 5
1.4.2 Easy and Expert configuration modes ................................................................................................................ 5
1.4.3 On-line and Off-line configuration ....................................................................................................................... 5
1.5 Tools and accessories required to configure and store a project ................................................................................ 5
1.5.1 Configuring and saving a new project................................................................................................................. 5
1.5.2 Continuing or modifying the configuration of a saved project ............................................................................. 6
2. Commissioning, start-up and basic settings of the TX100................................................................................................ 6
2.1 Commissioning the TX100 .......................................................................................................................................... 6
2.1.1 Inserting rechargeable batteries or dry-cell batteries.......................................................................................... 6
2.1.2 Battery life and load ............................................................................................................................................ 6
2.1.3 USB connector (only on TX100 USB)................................................................................................................. 7
2.1.4 Smartcard reader (only on TX100 SM) ............................................................................................................... 7
2.2 Starting up the TX100.................................................................................................................................................. 8
2.3 Basic settings .............................................................................................................................................................. 8
2.3.1 Access to the setting........................................................................................................................................... 8
2.3.2 Time and day setting .......................................................................................................................................... 9
2.3.3 Activation of the sounds...................................................................................................................................... 9
2.3.4 Language selection............................................................................................................................................. 9
2.3.5 Format of the ETS group addresses................................................................................................................. 10
2.3.6 Activation of the display backlight ..................................................................................................................... 10
2.3.7 Activation of the ETS mode .............................................................................................................................. 10
2.3.8 Coupler selection .............................................................................................................................................. 11
2.3.9 Setting of the display contrast........................................................................................................................... 11
3. Projects management..................................................................................................................................................... 12
3.1 Loading or creating a project when starting up the TX100 ........................................................................................ 12
3.1.2 New project....................................................................................................................................................... 12
3.1.1 Current project .................................................................................................................................................. 12
3.1.3 "Project name" .................................................................................................................................................. 12
3.1.4 Old format project ............................................................................................................................................. 13
3.2 Projects management................................................................................................................................................ 14
3.2.1 Access to the projects management................................................................................................................. 14
3.2.2 Saving a project ................................................................................................................................................ 14
3.2.3 Creation of an installation ................................................................................................................................. 16
3.2.4 Loading of a project .......................................................................................................................................... 16
3.2.5 Deletion of a project.......................................................................................................................................... 18
3.2.6 Display of the basic data of a project file .......................................................................................................... 19
4. Choice of the On-line or Off-line configuration mode...................................................................................................... 20
5. On-line configuration in Easy mode of a new installation ............................................................................................... 21
5.1 The various steps of the configuration....................................................................................................................... 21
5.2 Check of the installation and of the material required for the configuration............................................................... 21
5.3 Coupling and assigning the TX100 to the installation................................................................................................ 22
5.4 Learning of the installation and numbering of the inputs and outputs ....................................................................... 24
5.5 Assigning a function to an input................................................................................................................................. 29
5.6 Creation of links and input of additional parameters ................................................................................................. 31
5.7 Creation of links and input of additional parameters ................................................................................................. 34
5.8 Vizualizing the links ................................................................................................................................................... 36
6. Off-line configuration of a new installation in Easy mode ............................................................................................... 36
7. Modifying the configuration of an installation .................................................................................................................. 37
7.1 General indications about the modifications of a KNX installation ............................................................................ 37
7.2 Removing links .......................................................................................................................................................... 37
8. On-line configuration of a new installation in Expert mode ............................................................................................. 39
8.1 General points ........................................................................................................................................................... 39
8.2 Description of the Expert mode ................................................................................................................................. 40
8.3 Configuring in Expert mode....................................................................................................................................... 43
9. Maintenance and adjustment help tools ......................................................................................................................... 46
9.1 Management of the products of an installation.......................................................................................................... 46
9.2 Installation management ........................................................................................................................................... 49
9.3 Updating the software of the TX100 .......................................................................................................................... 51
9.4 Learning an installation.............................................................................................................................................. 54
9.5 Measuring tools ......................................................................................................................................................... 60
9.6 Simulation.................................................................................................................................................................. 62
Summary
To Next Page
Loading...
