What to do if my Haier HW100-14829 fails to operate?
If your Haier Washer isn't operating, here's what to check: * Ensure the program has been started. * Verify the door is properly closed. * Make sure the machine is switched on. * Check the power supply. * Deactivate the child lock, if it's enabled.
How to reduce strong vibration while spinning in Haier HW100-14829?
To stop strong vibrations while spinning in your Haier Washer: * Remove all transportation bolts. * Ensure the appliance is on solid, level ground. * Check and correct the load weight and balance.
Why is my Haier HW100-14829 draining constantly?
If your Haier Washer is not draining properly, it could be due to several reasons. Ensure the drain hose is correctly installed and not placed in water. The cause may be that the height of the drain hose is below 80 cm or the drain hose end could reach into water.
Why is my Haier HW100-14829 spinning failing?
If spinning fails in your Haier Washer, check the machine load and laundry for unbalance and run a spinning programme again. The cause may be unbalance of laundry.
Why is there no water in my Haier Washer?
If your Haier Washer isn't filling with water, check the following: * Ensure the water tap is open. * Inspect the inlet hose for kinks. * Verify adequate water pressure. * Confirm the door is properly closed. * Ensure a consistent water supply.
What to do if my Haier HW100-14829 Washer has a drainage failure?
To address drainage failure in your Haier Washer, unblock the drain hose and ensure it is properly installed. The issue may be that the drain hose is blocked or the drain hose end is higher than 100 cm above the floor level.
Why does my Haier HW100-14829 Washer operation stop before completing wash cycle?
If your Haier Washer stops before completing the wash cycle, check both the power and water supply. The cause may be water or electric failure.
How to fix UNB error on Haier HW100-14829 Washer?
If your Haier Washer shows a UNB error, it means there's an unbalanced load. To fix this, check and balance the laundry load in the drum and reduce the load if necessary.
Why does my Haier HW100-14829 operation stop for a period of time?
If your Haier Washer displays an error code or the operation stops for a period of time, consider display codes, reduce or adjust the load. It may also be because the programme performs soaking cycle or detergent is not appropriate or excessive use of detergent. You may need to cancel the programme and restart.
How to get rid of excessive foam in my Haier HW100-14829?
If you notice excessive foam in the drum or detergent drawer of your Haier Washer, check the detergent recommendations and reduce the amount of detergent used.
General| Washing Capacity | 10 kg |
|---|---|
| Spin Speed | 1400 RPM |
| Energy Efficiency Class | A+++ (-30%) |
| Number of Programs | 16 |
| Noise level washing | 53 dB |
| Noise level spinning | 72 dB |
| Depth | 60 cm |
| Loading type | Front |
| Dimensions (H x W x D) | 85 cm x 60 cm x 60 cm |
Safety precautions before initial appliance operation.
General safety instructions for everyday appliance use.
Safety advice for cleaning and maintaining the appliance.
Essential safety measures for appliance installation.
Guidelines on proper usage and overall appliance warnings.
Operation of core control panel buttons for power, program selection, and cycle control.
Procedures for starting, interrupting, cancelling, and completing wash cycles.
Identifies problems with display codes and provides corresponding solutions.
Solutions for typical problems not indicated by display codes.
Addresses motor errors, load issues, foam, and procedures for power interruptions.
Essential step to remove transit bolts before operating the machine.
Instructions for connecting the drain hose, water inlet, and electrical power.
To Next Page