What to do if water level not reached in my Haier Washer?
If the water level isn't reached in your Haier Washer after 8 minutes, and the drain hose is self-syphoning, make sure the tap is fully opened, the water pressure is normal, and check the drain hose installation.
Why is my Haier HW100-BP14959S6 Washer vibrating so much?
If your Haier Washer is vibrating excessively during operation, consider the following: * Ensure that all transportation bolts have been removed from the machine. * Confirm the washer is placed on a solid, level surface. * Check the weight and balance of the load inside the drum.
How to fix a drainage failure in my Haier Washer?
If your Haier Washer is experiencing drainage failure, try these steps: * Unblock the drain hose to ensure there are no obstructions. * Clean the pump filter to remove any debris. * Make sure the drain hose is properly installed to allow for effective drainage.
What to do if spinning fails on my Haier HW100-BP14959S6 Washer?
If the spinning cycle fails on your Haier Washer, it might be due to an unbalanced load of laundry. Check the machine load and laundry distribution, then run the spinning program again to see if that resolves the issue.
Why is my Haier HW100-BP14959S6 Washer not washing clothes properly?
If you're not happy with the wash results from your Haier Washer, consider these points: * The selected program may not be suitable for the degree of dirtiness. * You may not have used enough detergent. * The maximum load may have been exceeded. * The laundry may have been unevenly distributed in the drum. To improve results: * Select a more appropriate program. * Use the correct amount of detergent for the dirtiness and follow the detergent manufacturer's instructions. * Reduce the load size. * Loosen the laundry in the drum.
Why does my laundry have grey patches after washing in my Haier Washer?
If your laundry has grey patches after washing in your Haier Washer, it's likely caused by fats like oils, creams, or ointments. You should pretreat the laundry with a special cleaner before washing.
Why is there excessive foam in my Haier Washer?
If you notice excessive foam in your Haier Washer, it might be because the detergent you're using isn't appropriate. Check the detergent recommendations in the manual or on the detergent packaging.
How to remove washing powder residues from laundry in my Haier HW100-BP14959S6?
If you find washing powder residues on your laundry after a cycle in your Haier Washer, this can be due to insoluble particles in the detergent. You can perform an extra rinse, try brushing the spots off the dry laundry, or switch to a different detergent.
What to do if my Haier HW100-BP14959S6 Washer has a drainage error?
If your Haier Washer shows a drainage error because water isn't fully drained within 6 minutes, you should: * Clean the pump filter. * Check the drain hose installation.
How to fix an unbalanced load error on my Haier HW100-BP14959S6?
If your Haier Washer displays an unbalanced load error, check the laundry load in the drum and balance it. You might need to reduce the load size to ensure proper balance during the wash cycle.
General| Capacity | 10 kg |
|---|---|
| Spin Speed | 1400 rpm |
| Energy Efficiency Class | A+++ |
| Weight | 72 kg |
| Inverter Motor | Yes |
| Programs | 15 |
| Display | LED |
| Type | Front Load |
Ensure no transport damage, remove packing, keep away from children, and handle with two persons.
Applies to children aged 8+. Keep young children away. Do not let children or pets near open door. Store detergents safely.
Enable additional options: Delay, Temp., Speed, Extra Rinse, Steam, Start/Pause, and Child Lock.
Table detailing programmes (Cotton, Mix, etc.) with load capacity, temperature, fabric type, spin speed, and function options.
Load laundry piece by piece. Select appropriate detergent. Add detergent to drawer. Switch on, select programme, and add options.
Start, interrupt, or cancel programmes. Post-wash procedures and buzzer settings.
Lists problems (e.g., drainage error, lock error, water level) with causes and solutions.
Addresses issues like machine not operating, not filling, draining while filling, vibration, stopping, foam, and washing results.
Fix drain hose to piping, height 80-100 cm. Warning: Use supplied hose, connect to cold water.
Connect water inlet hose and electrical plug. Ensure all connections are firm, dry, and leak-free.
To Next Page