What to do if my Haier Washer fails to operate?
If your Haier Washer isn't starting, here's what to check: * Make sure you've selected a program and started it. * Ensure the door is fully closed. * Verify the machine is switched on. * Check that the power supply is working. * Deactivate the child lock if it's enabled.
How to fix an unbalanced load error on my Haier HW100-BP14959S6?
If your Haier Washer displays an unbalanced load error, check the laundry load in the drum and balance it. You might need to reduce the load size to ensure proper balance during the wash cycle.
Why does my Haier HW100-BP14959S6 Washer keep filling with water?
If your Haier Washer is constantly filling with water, check these: * Ensure the water tap is functioning correctly. * Inspect the inlet hose for any issues. * Unblock the inlet hose filter to ensure proper water flow. * Verify that the water pressure is adequate. * Confirm the door is properly closed. * Ensure the water supply is connected.
Why does my Haier HW100-BP14959S6 operation stop for a period of time?
If your Haier Washer's operation stops for a period of time, consider display codes, reduce or adjust the load, or cancel the programme and restart it.
Why does spinning fail on my Haier Washer?
Spinning may fail on your Haier Washer due to an unbalance of laundry. Check the machine load and laundry, and then run a spinning programme again.
How to fix drainage failure in Haier HW100-BP14959S6 Washer?
To address a drainage failure in your Haier Washer, try these steps: First, unblock the drain hose. Second, clean the pump filter. Finally, ensure the drain hose is properly installed.
Why is my Haier HW100-BP14959S6 Washer not washing clothes properly?
If you're not happy with the wash results from your Haier Washer, consider these points: * The selected program may not be suitable for the degree of dirtiness. * You may not have used enough detergent. * The maximum load may have been exceeded. * The laundry may have been unevenly distributed in the drum. To improve results: * Select a more appropriate program. * Use the correct amount of detergent for the dirtiness and follow the detergent manufacturer's instructions. * Reduce the load size. * Loosen the laundry in the drum.
What to do if spinning fails on my Haier HW100-BP14959S6 Washer?
If the spinning cycle fails on your Haier Washer, it might be due to an unbalanced load of laundry. Check the machine load and laundry distribution, then run the spinning program again to see if that resolves the issue.
How to fix a drainage failure in my Haier Washer?
If your Haier Washer is experiencing drainage failure, try these steps: * Unblock the drain hose to ensure there are no obstructions. * Clean the pump filter to remove any debris. * Make sure the drain hose is properly installed to allow for effective drainage.
Why is my Haier HW100-BP14959S6 Washer vibrating so much?
If your Haier Washer is vibrating excessively during operation, consider the following: * Ensure that all transportation bolts have been removed from the machine. * Confirm the washer is placed on a solid, level surface. * Check the weight and balance of the load inside the drum.
General| Capacity | 10 kg |
|---|---|
| Spin Speed | 1400 rpm |
| Energy Efficiency Class | A+++ |
| Weight | 72 kg |
| Inverter Motor | Yes |
| Programs | 15 |
| Display | LED |
| Type | Front Load |
Ensure no transport damage, remove packing, keep away from children, and handle with two persons.
Applies to children aged 8+. Keep young children away. Do not let children or pets near open door. Store detergents safely.
Enable additional options: Delay, Temp., Speed, Extra Rinse, Steam, Start/Pause, and Child Lock.
Table detailing programmes (Cotton, Mix, etc.) with load capacity, temperature, fabric type, spin speed, and function options.
Load laundry piece by piece. Select appropriate detergent. Add detergent to drawer. Switch on, select programme, and add options.
Start, interrupt, or cancel programmes. Post-wash procedures and buzzer settings.
Lists problems (e.g., drainage error, lock error, water level) with causes and solutions.
Addresses issues like machine not operating, not filling, draining while filling, vibration, stopping, foam, and washing results.
Fix drain hose to piping, height 80-100 cm. Warning: Use supplied hose, connect to cold water.
Connect water inlet hose and electrical plug. Ensure all connections are firm, dry, and leak-free.
To Next Page