What does CLR FLTR mean on my Haier Washer?
If your Haier Washer is displaying 'CLR FLTR', it indicates a drainage error where water isn't fully drained within 6 minutes. Check the drain hose installation.
Why is my Haier Washer not working?
If your Haier Washer isn't operating, several factors could be at play. First, ensure the program has actually been started. Then, check that the door is properly closed and the machine is switched on. A power failure could also be the culprit, so verify the power supply. Lastly, confirm that the child lock isn't activated.
Why is my Haier HW100-B14979S Washer vibrating so much?
If your Haier Washer is experiencing strong vibrations during spinning, there are a few potential causes. First, check that all transportation bolts have been removed. Next, ensure the appliance is on solid, level ground. Finally, verify that the machine load is correct and balanced.
Why is there no water in my Haier HW100-B14979S Washer?
If your Haier Washer isn't filling with water, start by checking the water tap to make sure it's open. Inspect the inlet hose for any kinks that might be blocking the water flow. Also, check that the water pressure is at least 0.03 MPa. Ensure the door is properly closed and that there isn't a water supply failure.
Why is my Haier HW100-B14979S Washer not spinning?
If your Haier Washer fails to spin, check the machine load and laundry, and then run a spinning program again.
What to do if my Haier HW100-B14979S shows CLR FLTR error?
If the Haier Washer displays 'CLR FLTR', it indicates a drainage error where water isn't fully drained within 6 minutes. You should clean the pump filter and check the drain hose installation. It may also mean the door is not shut properly, the water level was not reached after 12 minutes, or that the drain hose is self-syphoning. Make sure that the tap is fully opened and water pressure is normal. Check the drain hose installation. In the case of a water protective level error or a temperature sensor error, contact After sales service.
What to do if my Haier HW100-B14979S stops mid-cycle?
If your Haier Washer cycle stops before completing, the issue might be related to the water or electric supply. Check both the power and water supply to ensure they are functioning correctly.
Why does my Haier HW100-B14979S leave powder on clothes?
If your Haier Washer leaves washing powder residues on the laundry, it may be due to insoluble particles of detergent. Try performing an extra rinse, brushing the points from the dry laundry, or choosing another detergent.
Why is my Haier Washer not cleaning properly?
If the washing result from your Haier Washer is not satisfactory, it could be due to several reasons. The selected program might not be suitable for the degree of pollution. You might not have used enough detergent. The maximum load might have been exceeded, or the laundry might have been unevenly distributed in the drum. Try selecting another program, using more detergent according to the degree of pollution and the manufacturer's instructions, reducing the load, or loosening the laundry.
Why is my Haier HW100-B14979S Washer constantly draining?
If your Haier Washer is draining on its own, it could be because the drain hose is not installed correctly. Ensure the height of the drain hose is at least 80 cm and that the drain hose end is not submerged in water.
General| Model | HW100-B14979S |
|---|---|
| Loading type | Front Load |
| Capacity | 10 kg |
| Spin Speed | 1400 RPM |
| Energy Rating | A+++ |
| Energy efficiency class | A+++ |
| Dimensions (H x W x D) | 85 x 60 x 60 cm |
| Weight | 70 kg |
| Color | White |
| Delay Start | Yes |
| Child Lock | Yes |
Alerts to immediate risks like suffocation and necessary precautions.
Essential safety procedures before the first operation of the appliance.
Safety instructions for daily use, including handling children and pets.
Key safety aspects to consider during appliance installation.
Instructions for power/water connections and preparing laundry.
Troubleshooting guide for issues indicated by specific error codes.
Steps for unpacking and removing all transportation bolts.
To Next Page