28 | Hampton
®
H27E-11 Direct Vent Freestanding Gas Stove
installation
Outside Wall
Mur extérieur
Furring
Strips
Fourrures en bois
Furstrp.eps
see also c34020a.eps
furstrpf.eps
french
Note: The pipe seam should
be facing down.
Note: To make the installation more aes-
thetically pleasing, we recommend
framing out a square that the cap
can be mounted on.
3) Attach the 4" dia. flex liner to the vent terminal
ensuring that the flex overlaps the collar of the
vent terminal by a minimum of 1-3/8"(35mm).
Use Mill-Pac to seal and secure with 3 of the
#8 x 1/2" screws (stainless steel).
4) Attach the adjustable pipe section to the vent
terminal using Mill-Pac attach with 3 of the #8
x 1/2" screws (stainless steel).
NOTE: For best results and optimum perfor-
mance with each approved venting
system, it is highly recommended to
apply “Mill-Pac” sealant (supplied) to
every inner pipe connection. Failure
to do so may result in drafting or
performance issues not covered
under warranty.
Note: If installing ter-
mination on a
siding covered
wall, a vinyl sid-
ing standoff or
furring strips
must be used to
ensure that the
termination is
not recessed into the siding. For
vinyl siding standoff installation
refer to the Dura-Vent Termination
instructions.
5) Slide the partially connected pipe and vent
terminal assembly through the wall thim-
bles (from the exterior into the interior) and
secure the cap to the exterior wall with 4 of
the supplied screws (#8 x 1-1/2" drill point,
stainless steel). Note: pilot holes will need
to be drilled through the wall thimble on all
4 corners.
Note: The four screws provided for the
vent cap should be replaced with
appropriate fasteners for stucco,
brick, concrete, or other types of
sidings.
6) A bead of non-hardening mastic should be
run around both the termination and vinyl
siding standoff to prevent water from entering
and to make a tight seal between the cap
and the standoff.
7) Stretch the 4" dia. flex liner out fully and get
a trial fit of the liner onto the 4" dia. starter
collar.
8) Cut the 4" dia. flex liner to the desired size.
Hint: leave an extra 12" to 16" of length, this
will make the final assembly easier to work
with.
9) Secure the 4" dia. flex liner to the 4" adapter with
Mill-Pac and 3 of the #8 x 1/2" screws (stainless
steel).
10) Slide the decorative Thimble Cover over the pipe
sections and secure with 4 screws (#8 x 1-1/2"
drill point, black) to the wall.
11) Slide the 90
o
elbow (crimp end up), the 45
o
elbow and the 4 ft. pipe section (crimp end up)
over the 4" dia. flex liner.
12) Install the spring spacers onto the pipe sections.
13) Secure the 4" dia. flex liner with adapter onto
the stove collar. Put a bead of Mill-Pac around
the appliance adapter and secure with 3 screws
(#8 x 1/2, stainless steel).
14) Attach the 45
o
elbow onto the starter collar by
sealing with Mill-Pac securing with 3 of the #8
x 1/2" (black) screws.
15) Attach the pipe section to the 45
o
elbow by
sealing with Mill-Pac securing with 3 of the #8
x 1/2" screws (black). Pipe seams should be
facing the wall.
16) Attach the 90
o
elbow onto the pipe section by
sealing with Mill-Pac securing with 3 of the #8
x 1/2" screws (black).
17) Slide the adjustable pipe section onto the 90
o
elbow. Slide the trim collar over the adjustable
pipe sections to cover the joint of the telescopic
section. The flex may have to be compressed
back in order for the adjustable pipe to properly
mate to the elbow. Seal with Mill-Pac secure with
3 of the #8 x 1/2" screws (black). Pipe seams
facing down.
18) Install the trim collar over the starter collar and
secure with a #8 x 1/2" screw (black).
If the pipe needs to be touched up, use only Stove
Brite High Temperature Metallic Black Stove Paint.
To Next Page
Loading...
