What does M2 Motor Error mean on my Handicare Puma 20?
The M2 Motor Error indicates that a motor has become disconnected. Check the motors, cables, and connections to the control system. If the error persists after these checks, the Power Module may be defective.
What does it mean when the ON/OFF light flashes 9 times on my Handicare Puma 20 Wheelchair?
If the ON/OFF light flashes 9 times on your Handicare Wheelchair, it indicates a 'BUS low' fault. This is due to cable breakage (in one of the DX bus cables) or a short circuit in the DX bus system (entrances to the modules). Check the cables and the modules, and replace if necessary.
What does User Switch detached mean on my Handicare Scooter?
The 'User Switch detached' message on your Handicare Scooter means that the Omni has detected that the User Switch has become disconnected. Check all cables and connectors between the Omni and the User Switch.
What does Left Indicator Lamp Short mean on my Handicare Scooter?
A 'Left Indicator Lamp Short' on your Handicare Scooter means that the control system has detected a short in either of the Indicator Circuits. Check the indicators, cables, and connections to the control system. If the error persists after the above checks have been made, then the ISM may be defective.
What does it mean if the ON/OFF light flashes twice on my Handicare Scooter?
If the ON/OFF light flashes twice on your Handicare Scooter, it indicates a DX accessory fault. The module displays a fault as a result of a programming fault or short circuit and/or overload of the accessories.
What does 'System Error' mean on my Handicare Wheelchair and how can I fix it?
A 'System Error' indicates a fault that cannot be attributed to a specific module. Check all cables and connections. Cycle the power. If the error persists and the system contains 3rd party Modules: Disconnect all the none PGDT modules and cycle the power. If this has cleared the trip: Connect each 3rd party module in turn, cycling the power each time. If the trip reappears after one of the power cycles then the last module to have been added to the system must be defective. If the error persists, the PGDT control system may be defective.
How to fix a Joystick Calibration Error on a Handicare Puma 20?
A Joystick Calibration Error indicates that the Joystick Calibration process was unsuccessful. Enter OBP and attempt calibration. If the error persists, the Joystick Module may be defective.
What does it mean when the service indicator flashes once on Handicare Puma 20 Wheelchair?
This is likely a 'STALL' timeout caused by user error. Place the joystick in neutral and try again.
What does 'Inhibit Active' mean on my Handicare Puma 20 Wheelchair and how do I resolve it?
An 'Inhibit Active' error means that one of the Inhibit inputs is active and in a latched state. Cycle the power, which will drop out of Latched Mode and might clear the error. Check all wiring and switches connected to the indicated Inhibits. If the error persists, the ISM may be defective.
What does 'Latched Timeout' mean on my Handicare Puma 20 Wheelchair and how can I fix it?
A 'Latched Timeout' error means the control system has detected that the programmed Latched Timeout time has been exceeded. Cycle the power and initiate Latched Mode. If the error persists, the Input Device may be defective.
General| Type | Power Wheelchair |
|---|---|
| Foldable | No |
| Footrests | Yes |
| Seat Width | 40-48 cm |
| Seat Depth | 40-48 cm |
| Backrest Height | 40-50 cm |
Advises on avoiding contact with hot motors and parts exposed to direct sunlight to prevent burns.
Warns users to avoid contact with moving components like motors and wheels to prevent injury.
Provides guidance on operating the wheelchair in various environments and outlines safety precautions.
Lists essential checks to perform before driving the wheelchair to ensure safe operation.
Explains safe procedures for transferring into and out of the wheelchair.
Instructions on operating the controller and joystick, handling curves, braking, emergency stops, and slope operation.
Crucial safety information and requirements for transporting the wheelchair in a vehicle.
Explains the correct procedure for fastening the seat belt to ensure occupant safety during transport.
Details the recommended schedule for daily, weekly, monthly, and annual maintenance tasks.
Covers battery types, charging procedures, and essential maintenance for optimal performance.
Lists common checks to perform if the wheelchair is not functioning correctly.
To Next Page
