What does it mean when the ON/OFF light flashes 5 times on my Handicare Puma 20 Wheelchair?
If the ON/OFF light flashes 5 times, it indicates that the m1 parking brake connection is faulty or loose, or the m1 parking brake is defective. Correct the connection. If the parking brake is defective, replace the drive motor.
What should I do if the ON/OFF light flashes four times on my Handicare Puma 20?
If the ON/OFF light flashes four times, it could mean the m2 motor connection is faulty or loose, the m2 motor is defective, there's a short circuit in the m2 motor connections, or there's a defective power module output. Check and secure the motor connection. If that doesn't work, replace the motor. Correct any short circuits in the connections. Check the motor for defects, as a defective motor can cause a power module output to fail. Only replace the power module if the fault occurs immediately upon switching the unit on; otherwise, replace the entire drive unit.
What does it mean when the ON/OFF light flashes 12 times on my Handicare Puma 20 Wheelchair?
If the ON/OFF light flashes 12 times, it indicates that the system does not 'fit' because the system modules are not compatible. Program the entire drive system for the relevant wheelchair using the DX-Wizard program on a PC. Always confirm the programming by switching the wheelchair on and off.
What does it mean when the ON/OFF light flashes four times on my Handicare Puma 20 Wheelchair?
If the ON/OFF light flashes four times, it means that either the connection of the m2 motor is faulty or the m2 motor is defective. Check the motor connections and cabling. If the problem persists, replace the m2 motor.
What does it mean when the ON/OFF light flashes 11 times on my Handicare Wheelchair?
If the ON/OFF light flashes 11 times on your Handicare Wheelchair, it indicates a 'STALL' overload fault, meaning a motor is continually demanding too much power. Check the drive units. This fault is often caused by obstacles that are too high, or driving against walls and door frames, etc. It may also be caused by a difficult turn from a standing position.
What does it mean when the service indicator flashes twice and the ON/OFF light flashes three times on a Handicare Wheelchair?
This indicates a battery fault or a defective M1 motor. Check the batteries and cabling, charge or replace the batteries, and check the motor connections and cabling. If the issue persists, the M1 motor may need to be replaced.
Why is the ON/OFF light flashing 7 times on my Handicare Puma 20 Wheelchair?
If the ON/OFF light on your Handicare Wheelchair flashes 7 times, it indicates that the battery voltage is low, or the batteries are flat or bad. Charge or replace the batteries. Note that if the voltage is low (below 12 V), the electronics will not function correctly.
How to fix a joystick error on my Handicare Puma 20?
A joystick error on your Handicare Wheelchair often occurs if the joystick is not centered when the control system is powered on. Ensure the joystick is centered and then power up the control system. If the error continues, the joystick or Joystick Module may be defective.
What to do if my Handicare Puma 20 displays a high battery error?
A high battery error on your Handicare Wheelchair means the control system has detected a battery voltage above 35V. Verify the condition of the batteries and their connections to the control system. If the error persists after checking the batteries and connections, the Power Module may be defective.
Why does my Handicare Puma 20 show a low battery error?
A low battery error on your Handicare Wheelchair indicates that the control system has detected a battery voltage below 16V. Check the condition of the batteries and their connections to the control system. If the error persists after checking the batteries and connections, the Power Module may be defective.
General| Type | Power Wheelchair |
|---|---|
| Foldable | No |
| Footrests | Yes |
| Seat Width | 40-48 cm |
| Seat Depth | 40-48 cm |
| Backrest Height | 40-50 cm |
Advises on avoiding contact with hot motors and parts exposed to direct sunlight to prevent burns.
Warns users to avoid contact with moving components like motors and wheels to prevent injury.
Provides guidance on operating the wheelchair in various environments and outlines safety precautions.
Lists essential checks to perform before driving the wheelchair to ensure safe operation.
Explains safe procedures for transferring into and out of the wheelchair.
Instructions on operating the controller and joystick, handling curves, braking, emergency stops, and slope operation.
Crucial safety information and requirements for transporting the wheelchair in a vehicle.
Explains the correct procedure for fastening the seat belt to ensure occupant safety during transport.
Details the recommended schedule for daily, weekly, monthly, and annual maintenance tasks.
Covers battery types, charging procedures, and essential maintenance for optimal performance.
Lists common checks to perform if the wheelchair is not functioning correctly.
To Next Page
