Handicare Puma 20 User Manual (English)

Other manuals for Handicare Puma 20

Questions and Answers:

D
Dana LoweryAug 26, 2025
What to do if my Handicare Wheelchair ON/OFF light doesn't turn on and it won't move?
- K
  Kyle BlackwellAug 26, 2025
  If the ON/OFF light doesn't illuminate and the wheelchair remains stationary, several factors could be at play. First, ensure the controller plug is correctly inserted into the power module. Additionally, inspect the fuses and replace any that are defective. Verify that the batteries are properly connected and that all connections are secure. If this is a 'STALL' timeout, place the joystick in neutral and try again.
B
bbakerAug 25, 2025
What does it mean if ON/OFF light flashes once on Handicare Mobility Aid?
- L
  Lynn TurnerAug 26, 2025
  If the ON/OFF light on your Handicare Mobility Aid flashes once, it indicates a faulty DX module. Replace one or more modules. The 'on/off' LED indicates the condition of the entire system, while each module has a separate status LED to help identify the faulty one.
L
lowepatriciaAug 25, 2025
How to fix service indicator flashes once on Handicare Mobility Aid?
- B
  butlerlauraAug 26, 2025
  If the service indicator flashes once on your Handicare Mobility Aid, it's likely a 'STALL' timeout due to user error. Place the joystick in neutral and try again.
A
Anthony WoodAug 25, 2025
What to do if service indicator flashes twice and ON/OFF light flashes three times on Handicare Mobility Aid?
- D
  deborah60Aug 25, 2025
  If the service indicator flashes twice and the ON/OFF light flashes three times on your Handicare Mobility Aid, it could indicate a battery fault. Check the batteries and cabling, and try charging or replacing the batteries. Also, inspect the motor connections and cabling. Alternatively, the m1 motor may be defective, requiring replacement.
Y
yzimmermanAug 30, 2025
How to fix a Joystick Calibration Error on a Handicare Puma 20?
- D
  dennis81Aug 30, 2025
  A Joystick Calibration Error indicates that the Joystick Calibration process was unsuccessful. Enter OBP and attempt calibration. If the error persists, the Joystick Module may be defective.
J
Joyce KingSep 4, 2025
What to do if my Handicare Scooter ON/OFF light doesn't turn on and the wheelchair won't move?
- L
  Lee HansenSep 4, 2025
  If the ON/OFF light doesn't illuminate and the Handicare Scooter remains stationary, consider these potential causes and solutions: * Ensure the controller plug is correctly inserted into the power module. It may be a stall timeout, place the joystick in neutral and try again. * Inspect the fuses and replace any that are defective. * Verify that the batteries are properly connected. * Check for loose battery connections and secure them.
D
Dr. Stanley MarshSep 4, 2025
What does it mean when the ON/OFF light flashes twice on my Handicare Puma 20 Wheelchair?
- R
  Rhonda CarrSep 4, 2025
  If the ON/OFF light flashes twice, it could mean the DX accessory is faulty due to a programming fault or short circuit/overload of the accessories. Alternatively, if the electrical high/low adjustment is not in the lowest position, the LED will flash twice to indicate that the speed limitation has been switched on, causing the wheelchair to drive more slowly.
D
debbiegilbertSep 3, 2025
What does it mean when the ON/OFF light flashes once on my Handicare Puma 20?
- C
  Crystal HoldenSep 4, 2025
  If the ON/OFF light flashes once, it indicates that the DX module is faulty. Replace one or more modules. The 'on/off' LED indicates the condition of the entire system. The modules all have a separate status LED: in this way, you can see which one is faulty.
S
Shawn EllisSep 3, 2025
What should I do if my Handicare Wheelchair displays 'Charging' as an error?
- D
  David LewisSep 3, 2025
  If an On-Board Charger is used: Disconnect the charger from the AC supply. If an Off-Board Charger is used: Disconnect the charger from the Wheelchair. If the trip is still present after the charger has been disconnected then the Joystick Module may be defective.
D
Danielle JamesSep 3, 2025
What does 'User Switch detached' mean on my Handicare Puma 20?
- V
  vlewisSep 3, 2025
  A 'User Switch detached' error means the Omni has detected that the User Switch has become disconnected. Check all cables and connectors between the Omni and the User Switch. If the error persists, the User Switch may be defective. If it is required to use the Omni without a User Switch being connected, then the parameter, Switch Detect, should be set to Off. If a User Switch is not used the responsibility for that decision lies with the healthcare professional.