6
Rear
Panel
-
Audio
and
System
Connections
8
FM
Antenna: Connect an indoor
or external
FM
antenna to these
terminals. Note that the supplied
300 ohm to 75 ohm
adapter
is
required for connections from twin
lead or inside dipole antennas.
©
AM
Antenna: Connect the AM
loop antenna supplied with the
receiver to these terminals. If an
external AM antenna is used, make
connections to the
AM
and
GND
terminals in
accordance
with the
instructions supplied with the
antenna.
@ Tape 1 Out: Connect these jacks
to the RECORD/INPUT jacks of an
audio recorder.
@ Tape 1 In: Connect these jacks to
the PLAY/OUT jacks of an audio
recorder.
43
Tape 2 Out: Connect these jacks
to the RECORD/INPUT jacks of a
second audio recorder.
4)
Tape 2 In: Connect these jacks to
the PLAY/OUT jacks of a second
audio recorder.
©
CD
IN: Connect these jacks to
the output of a
compact
disc
player
or CD changer.
CD
Front
L:
Connect these terminals
to the front left speaker.
O Front R: Connect these terminals
to the front right speaker.
@)
Center: Connect these terminals
to the center speaker.
C)
Surround
L: Connect these ter-
minals to the left surround speaker.
()
Surround
R: Connect these ter-
minals to the right surround speaker.
@
Subwoofer
Pre-Out: Connect
this jack to the line level input of a
powered subwoofer.
If
an external
subwoofer amplifier is used,
connect
this jack to the subwoofer amplifier
input.
G)
Pre-Outs: If external power
amplifiers are used for any channels,
remove the connection pin and con-
nect the jack to the input of the
amplifier.
@ 6 Channel Direct Input: If an
external digital audio decoder is
used for
5.1
(Dolby AC-3) audio,
connect the outputs of that
decoder
to these terminals.
C) Multi
Room
Interface: For multi-
room installations where keypad
remotes are
in
use, connect the key-
pad
interface to this jack.
@ Multi IR: Connect the output of
an
IR
sensor
in
a remote room to this
jack to operate the AVR80's multi-
room control system.
U}
Multi-Out: When using the
AVR
80 for multi-room audio, connect this
jack to the input of the audio amplifi-
er powering the remote room speak-
ers.
{§)
Power
Cable: Connect the AC
plug to a non-switched AC wall
output.
$ONLY
O Switched
AC
Outlet: This outlet
may
be
used to
power
any device
that you wish to have on when the
unit is turned on.
(D Unswitched
AC
Outlet: This out-
let
may
be used to power any AC
device. The power will remain on at
this outlet regardless of whether the
AVR80 is on or off.
NOTE: The power consumption of
the device
plugged
into each of
these outlets should not exceed 120
watts.
0
Remote
IR In: If the AVR80's
front panel
IR
sensor is blocked due
to cabinet doors
or
other obstruc-
tions, an external
IR
sensor
may
be
used. Connect the output of the sen-
sor to this jack.
@
Remote
IR
Out:
This connection
permits the
IR
sensor in the receiver
to serve other remote controlled
devices. Connect this jack to the "IR
IN"
jack
on Harman Kardon
or
other
compatible equipment.
Rear
Panel
-
Video
Connections
B
VCR
1 Audio In: Connect these
jacks to the audio PLAY/OUT jacks
of a VCR.
I])
VCR
1 Audio Out: Connect
these jacks to the RECORD/IN audio
jacks of a VCR.
[!3
VCR
1 Video In: Connect these
jacks to the composite video
PLAY/OUT jacks of a VCR.
I!]
VCR
1 Video Out: Connect these
jacks to the composite video
RECORD/IN jacks of a VCR.
[§I
VCR
1 S Video Out: Connect
these jacks to the "S" video
RECORD/IN jacks of a VCR.
Iii
VCR
1 S Video In: Connect
these jacks to the
"S"
video
RECORD/OUT jacks of a VCR.
Information
Display
0 "Vlsual" Indicator: These indica-
tors display which input source is
being fed to the video monitor output.
@ Test: This indicator flashes when
the output levels are being set using
the built
in
test signal generator.
@)
Memo:
This indicator flashes
when the
Memo
button is pressed
when entering presets
and
other
information into the tuner's memory.
C, Auto: This indicator signifies that
the Automatic Tuning
mode
is in use
for
FM
broadcasts.
0 Tuned: This indicator lights when
an AM or
FM
station is properly
tuned
and
locked.
00
VCR
2
Audio
Out: Connect
these jacks to the audio jacks
RECORD/IN of a
second
VCR.
W
VCR
2
Audio
In: Connect these
jacks to the audio PLAY/OUT jacks
of a second VCR.
D
VCR
2 Video Out: Connect these
jacks to the composite video
RECORD/IN jacks of a second
VCR.
I!]
VCR
2 Video In: Connect these
jacks to the composite video
PLAY/OUT jacks of a second VCR.
13
VCR
2 S Video Out: Connect
these jacks to the
"S"
video
RECORD/IN jacks of a second VCR.
1]11
VCR 2 S Video In: Connect
these jacks to the
"S" video
RECORD/OUT jacks of a second
VCR.
0 Stereo: This indicator lights
when an
FM
station is broadcasting
in
stereo.
@ Volume Indication: The last two
indicators on the information display
indicate the volume level. Note that
□
dB
is the reference level, not an
indication that there is no output.
(i)
Tuner
Frequency
Indication:
When
the
tuner
is
in
use,
the
main
Information
Display
will
show
the
preset
channel
number,
if
any,
the
frequency
band
and
the
station
fre-
quency.
Indicators
at
the
right
side
of
the
display
show
kHz
when
an
LW
or
AM
station
is
tuned
or
MHz
when
an
FM
station
is
tuned.
li!i)
TV
Audio
In: Connect the audio
outputs of a
TV,
cable converter or
satellite receiver to these jacks.
W
TV
Video In: Connect the com-
posite video output of a
TV,
cable
converter or satellite receiver
to
this
jack. The signals received at this
jack are also used to trigger the
"TV Auto-On" feature.
[!]TVS
Video In: Connect the "S"
video output of a
TV,
cable converter
or satellite receiver
to
this jack.
[ii LD Audio ln: Connect the audio
output of a laser disc player to these
jacks.
[!I
LD Video In: Connect the com-
posite video output of a laser disc
player to this jack.
0 Main Information Display:
This ten
digit
display shows mes-
sages relating to the status,
input
source, surround mode, tuner, vol-
ume level
or
other
aspects
of the
unit's operation.
@ Multi: This indicator signifies that
the AVR80 is sending a program
source to a remote room location.
Note that it may
be
illuminated even
when the unit is "off" in the main lis-
tening room, signifying that opera-
tion continues at another location.
When a remote
command
is being
received via the
Multi
IR
connection,
this indicator will flash.
ACMUTS
120Y
6Cf!:!I
t]]
[]
Ii]
LD
S
Video
In: Connect the "S"
video output of a laser disc player to
this jack.
1§)
LD
Digital In: Connect the coax
digital output of a laser disc or CD
player to this jack.
NOTE: This connection is for stan-
dard, two channel PCM audio. DO
NOT connect the modulated
RF
digi-
tal output used for multichannel
(AC-3) audio to this jack.
ii
TV
Monitor Video Out: Connect
this
jack
to the composite video
input of a
TV
monitor or video pro-
jector to view the on screen control
menus and output of the receiver's
video switcher.
[D
TV
Monitor
S Video Out:
Connect this jack to the S video
input of a
TV
monitor
or
video pro-
jector to view
S video sources
selected
by
the receiver's video
switcher.
4D
Mode
Status: These indicators
display the currently selected
surround mode.
@ DISP: This indicator lights when
the FL
display
has been turned
off using the
Display button
iii]
to
remind you that the unit is still
turned on.
@
Copy
Indicators: The
TAPE
COPY
indicator lights when an input
other than the current source has
been selected to
copy
Tape
1.
The
VCR
COPY1
indicator signifies that
the input to VCR 1 is other than the
currently selected source.
4D
P-Scan: This indicator flashes
when the stations programmed into
the tuner memory are being auto-
matically reviewed.
@
Auto
Memo:
This indicator flash-
es when the tuner is automatically
scanning for stations
and
entering
them into the preset memory.
@ Signal Level Indication: This is
a visual indication of the strength of
a radio station signal. The more bars
visible, the stronger the station.
(
To Next Page
Loading...
