6
-------------------------------------------------
Rear
Panel
-
Audio
and
System
Connections
8 FM Antenna: Connect an indoor
or external
FM
antenna to these
terminals. Note that the supplied
300 ohm to 75 ohm adapter
is
required for connections from twin
lead or inside dipole antennas.
© AM Antenna: Connect the
AM
loop antenna supplied with the
receiver to these terminals. If
an
external AM antenna is used, make
connections to the AM and GND
terminals
in
accordance with the
instructions supplied with the
antenna.
@ Tape 1 Out: Connect these jacks
to the RECORD/INPUT jacks of an
audio recorder.
@ Tape 1 In: Connect these jacks to
the PLAY/OUT jacks of an audio
recorder.
@ Tape 2 Out: Connect these jacks
to the RECORD/INPUT jacks of a
second audio recorder.
()
Tape 2 In: Connect these jacks to
the PLAY/OUT jacks of a second
audio recorder.
@ CD IN: Connect these jacks to
the output of a
compact
disc player
or CD changer.
4D
Front
L:
Connect these terminals
to the front left speaker.
O Front
R:
Connect these terminals
to the front right speaker.
8 Center: Connect these terminals
to the center speaker.
C) Surround
L:
Connect these ter-
minals to the left surround speaker.
C) Surround
R:
Connect these ter-
minals to the right surround speaker.
@ Subwoofer Pre-Out: Connect
this jack to the line level input of a
powered subwoofer. If
an
external
subwoofer amplifier
is
used, connect
this jack to the subwoofer amplifier
input.
4?l
Pre-Outs: If external power
amplifiers are used for any channels,
remove the connection pin and con-
nect the jack to the input of the
amplifier.
@ 6 Channel Direct Input: If
an
external digital audio decoder
is
used for
5.1
(Dolby AC-3) audio,
connect the outputs of that decoder
to these terminals.
~
Multi Room Interface:
For
multi-
room installations where keypad
remotes are
in
use, connect the key-
pad interface to this jack.
® Multi IR: Connect the output of
an
IR
sensor
in
a remote
room
to
this
jack to operate the AVRB0's multi-
room control system.
Cl)
Multi-Out: When using the
AVR
80 for multi-room audio, connect this
jack to the input of the audio amplifi-
er powering the remote room speak-
ers.
@ Power Cable: Connect
the
AC
plug to a non-switched AC wall
output.
4DONLY
O Switched AC Outlet: This outlet
may be used to power any device
that you wish to have on when the
unit is turned on.
(!) Unswitched AC Outlet: This out-
let may be used to power any AC
device. The power will remain on at
this outlet regardless of whether the
AVRB0 is on or off.
NOTE: The power consumption of
the device
plugged
into each of
these outlets should not exceed 120
watts.
0 Remote IR In: If the AVRB0's
front panel
IR
sensor is blocked due
to cabinet doors or other obstruc-
tions, an external
IR
sensor may be
used. Connect the output of the sen-
sor to this jack.
(I)
Remote IR Out: This connection
permits the
IR
sensor
in
the receiver
to serve other remote controlled
devices. Connect this jack to the "IR
IN" jack on Harman Kardon or other
compatible equipment.
r.i.1
VCR 1 Audio
In:
jacks to the audio P
of a
VCR.
I;)
VCR 1 AudiQ
01
these jacks to the R
jacks of a
VCR.
,
[!I
VCR 1 Video
In:
jacks to the comprn
PLAY/OUT jacks of
I!]
VCR 1 Video
01
jacks to the comprn
RECORD/IN jacks c
l]I
VCR 1 S Video 1
these jacks to the
":
RECORD/IN jacks c
[ii VCR 1 S Video I
these jacks to the
":
RECORD/OUT jack
Information
Disph
~-
I
8"Vl'"'l"ll
tors display whi9h i
being fed to
the;vid
8 Test: This in~ic,
the output levels ar
the built
in
test
*igr
8 Memo: This
.ind
when the Memo
bl
when entering
pres
information into the
$ Auto: This indic
the Automatic
Tunir
for
FM
broadcasts.
0 Tuned: This ind
an AM or
FM
statio,
tuned and locked.
To Next Page
Loading...
