Revision C • 10/07
HARRIS CORPORATION
3-6
3 Operation
MONITOR CONTROL PANEL QUICK GUIDE,
CENTER COLUMN CONTROLS
CONTROL ROOM
All CR outputs use the same monitor source. The selected source is usually indicated by a lit
button but, if Auto Mic Switching is enabled (to switch between the Real Air source (typically EXT)
and a Synthetic Air source while a CR mic channel is On), then the Real Air button (typically EXT)
flashes to indicate Synthetic Air is the monitor source. Alternate monitor sources can be selected
using the CR Monitor Source Selector and Take button. Its name is shown in the Name Display,
which turns off all selector buttons.
The buttons in this section have removable lenses for custom labels that identify the source assigned
during console setup. Here are the assigned signals as shipped from the factor:
EXEX
EXEX
EX
T — T —
T — T —
T — When lit, typically assigns the Real Air audio to the Control Room monitor outputs.
SEND — SEND —
SEND — SEND —
SEND — When lit, assigns the Send bus to the Control Room monitor outputs.
TEL REC — TEL REC —
TEL REC — TEL REC —
TEL REC — When lit, assigns the Telco record output to the Control Room monitor outputs.
PGM 1-4 — PGM 1-4 —
PGM 1-4 — PGM 1-4 —
PGM 1-4 — When lit, assigns the selected Program bus to the Control Room monitor outputs.
LEVEL CONTROLS
CC
CC
C
ue — ue —
ue — ue —
ue — Adjusts the output level of the built-in cue speaker and dedicated CUE output.
TT
TT
T
alkalk
alkalk
alk
back — back —
back — back —
back — Adjusts the output level of the dedicated Talk to Control Room (TLK CR) output
and the talkback level into the Cue speaker (when Talk to Cue is set during console setup).
CONTROL ROOM MONITOR SOURCE
CR MCR M
CR MCR M
CR M
onitonit
onitonit
onit
or Sor S
or Sor S
or S
ourour
ourour
our
cc
cc
c
e Ne N
e Ne N
e N
ame Dame D
ame Dame D
ame D
isplaispla
isplaispla
ispla
y — y —
y — y —
y — Shows the selected monitor source name (selected
by the source selector) while the Next LED is off. When the Next LED is lit, it shows an alternate
source name that is being selected using the Source Selector. The alternate source is selected by
pressing TAKE. There is no display if a source is selected using the seven monitor source buttons.
SS
SS
S
ourour
ourour
our
cc
cc
c
e Se S
e Se S
e S
elecelec
elecelec
elec
tt
tt
t
or — or —
or — or —
or — A rotary encoder to alphanumerically list all of the alternate monitor
sources. Turning the selector turns on the Next LED. “No List” is displayed if no alternate sources
were assigned during console setup.
TT
TT
T
AKE — AKE —
AKE — AKE —
AKE — Press to select the alternate monitor source while the Next LED is lit. Has no effect if
pressed while the Next LED is off.
Option LED — Option LED —
Option LED — Option LED —
Option LED — This LED is not used at this time.
FADERS
MONITMONIT
MONITMONIT
MONIT
OR — OR —
OR — OR —
OR — 100mm fader for adjusting the volume of the Control Room monitor speakers.
It affects the level of the Control Room MON output.
HEADPHONE — HEADPHONE —
HEADPHONE — HEADPHONE —
HEADPHONE — 100mm fader for adjusting the volume of the operator’s headphones. It
affects the level of the Control Room OP H/P output.
.
To Next Page
Loading...
