EasyManua.ls Logo

Heath Zenith 5411 - User Manual

Heath Zenith 5411
20 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
© 2010 HeathCo LLC 595-4884-22
Model 5411
Motion Sensor Light
Control
TEST
Features
• Turnsonlightingwhenmotionisdetected.
• Automaticallyturnslightingoff.
• Photocellkeepsthelightingoffduringdaylighthours.
• LEDindicatesmotionwassensed(dayornight).
TEST 1 5 10
ON-TIME
Put the ON-TIME switch on the
bottomofthesensorintheTEST
position.
OPERATION
*resetstoAutoModeatdawn.
ON-TIME
TEST 1 5 10
...backon.
1Second
OFF then...
PuttheON-TIMEswitchinthe1,5,
or10minuteposition.
Manual mode only works at night
becausedaylightreturnsthesensor
toAUTO.
Flipthelightswitchoffforonesecond
thenbackontotogglebetweenAUTO
andMANUALMODE.
Manual mode works only with the
ON-TIME switchin the 1,5, or10
position.
Note:Whenrstturnedonwaitabout1
1
/
2
minutesfor
thecircuitrytocalibrate.
Thispackageincludes:
LightControl
Sensor
Cover
Plate
Bulb
Holders
PlasticHanger
RubberPlug
Gasket
6Screws
(3sizesincluded)
MountingStrap
MountingBolt
2Wire
Connectors
Requirements
• Thelightcontrolrequires120-voltsAC.
• IfyouwanttouseManualMode,thecontrolmustbe
wiredthroughaswitch.
• Some codes require installation by a
qualified electrician.
• Thisproductisintendedforusewiththeenclosed
gasketandwithajunctionboxmarkedforuseinwet
locations.
MeetstheENERGYSTAR
®
guidelines
whenusedwith120WMaxbulbs.
Mode: On-Time Works: Day Night
Test
5Seconds x x
Auto
1,5,or10Minutes x
Manual
ToDawn* x
AUTO
MANUAL MODE

Table of Contents

Questions and Answers

  • C
    Crystal DuncanJul 26, 2025
    How to fix Heath Zenith Controller lights that won't turn on?
    • J
      Joy WrightJul 26, 2025
      If the lights on your Heath Zenith Controller aren't turning on, here are a few things to check: 1. Ensure the light switch is turned on. 2. Check the flood lamp to see if it's loose or burned out, and replace it if necessary. 3. Verify that the fuse hasn't blown or the circuit breaker isn't turned off; replace the fuse or turn the breaker on. 4. If it's daytime, the daylight turn-off feature may be active; recheck after dark. 5. If this is a new installation, confirm the circuit wiring is correct. 6. Make sure the light control is aimed correctly to cover the desired area.
  • K
    Kathleen GarciaJul 31, 2025
    Why does my Heath Zenith Controller light stay on all the time?
    • S
      stephen04Aug 1, 2025
      If your Heath Zenith Controller light stays on continuously, it could be due to several reasons: 1. A flood lamp might be positioned too close to the light control or pointed at nearby objects, causing heat to trigger the light. Reposition the flood lamp away from the light control or those objects. 2. The light control could be picking up a heat source like an air vent, dryer vent, or a heat-reflective surface. Try reducing the range. 3. The light control might be in manual mode. Switch it to AUTO.
  • W
    wodonnellAug 5, 2025
    What to do if Heath Zenith Controller lights turn on for no reason?
    • B
      bowmanthomasAug 5, 2025
      If your Heath Zenith Controller lights are turning on for no apparent reason, consider these possibilities: * The light control may be sensing small animals or automobile traffic. Try re-aiming the light control. * The range might be set too high. Reduce the range to see if that resolves the issue.
  • D
    Dalton BarkerAug 10, 2025
    Why are my Heath Zenith Controller lights flashing on and off?
    • M
      Michael HallAug 10, 2025
      If your Heath Zenith Controller lights are flashing on and off, consider the following: 1. Heat or light from the flood lamps might be turning the light control on and off. Reposition the flood lamp away from the light control. 2. Heat being reflected from other objects may be causing the light control to turn on and off. Reposition the light control. 3. If the light control is in TEST mode, this flashing is normal during warm-up. 4. Light may be leaking through the flood lamp reflectors. Replace the flood lamps with new, high-quality PAR 38 lamps, ensuring the metal lamp protectors are installed.
  • J
    joshuajenningsAug 16, 2025
    Why does my Heath Zenith Controller turn on during the day?
    • D
      dudleystacieAug 16, 2025
      If your Heath Zenith Controller is turning on during the day, it could be because: 1. The light control may be installed in a relatively dark location, causing it to activate even in daylight. The fixture is operating normally under these conditions. 2. The light control is set to TEST mode. Set the control switch to 1, 5, or 10 minutes instead.
  • J
    Jordan BerryAug 20, 2025
    What does it mean when Heath Zenith Controller lights flash once then stay off?
    • A
      Ashley TranAug 21, 2025
      If your Heath Zenith Controller lights flash once and then stay off in manual mode, it's likely because the light control is detecting its own lights. Reposition the flood lamps to keep the area below the light control relatively dark.

Summary

Motion Sensor Light Control

Operation Modes Overview

Explains TEST, AUTO, and MANUAL modes, including time delay and day/night settings.

Installation Guide

Mode Switching Instructions

Provides a visual summary for switching between TEST, AUTO, and MANUAL modes.

Eave Mount Sensor Adjustment

Specific steps to rotate the sensor head for correct operation in eave installations.

Wiring the Light Control

Electrical Safety Precautions

Critical warning to turn off power at the circuit breaker or fuse before wiring.

Mounting Strap and Hanger Installation

Wire Connections

Mounting the Light Control

Cover Plate and Rubber Plug Installation

Bulb Holder Positioning and Adjustment

Testing and Adjustment Procedures

Initial Power Up and Calibration

Setting Controls for Testing

Sensor Aiming and Coverage Area

Guidance on loosening, rotating, and securing the sensor for optimal coverage.

Factors Affecting Sensor Aiming

Range Adjustment and False Triggering

Setting the Time Delay

Fire Hazard Warning

Warning against aiming bulbs at combustible surfaces within 3 feet to prevent fire risk.

Troubleshooting Common Issues

Lights Will Not Turn On

Solutions for issues like power, bulb condition, circuit, and incorrect aiming.

Lights On During Daylight

Explains causes for operation during daylight, related to location or TEST mode.

Lights Turn On For No Reason

Addresses false triggering from animals, traffic, or high range settings.

Lights Turn Off Too Late

Lights Stay On Continuously

Covers continuous operation due to heat sources, manual mode, or reflections.

Lights Flash On and Off

Explains causes of intermittent operation, such as heat from lamps or reflections.

Manual Mode Flashing Issue

Heath Zenith 5411 Specifications

General IconGeneral
Power Source (Push Button)Battery
Sensor RangeNot applicable
Detection AngleNot applicable
Time DelayNot applicable
Light SensitivityNot applicable
Load CapacityNot applicable
Coverage AreaNot applicable

Related product manuals