15
Dear Customer,
&RQJUDWXODWLRQVRQ\RXUSXUFKDVHRIWKLVLQQRYDWLYH
and high-qual ity HELIX product.
With the HELIX V EIGHT DSP, Audiotec Fischer
is setting new standards in the range of digital
DPSOL¿HUV
We wish you many hours of enjoyment with your
new HELIX V EIGHT DSP.
Yours,
AUDIOTEC FISCHER
General installation instructions for HELIX
components
7RSUHYHQWGDPDJHWRWKHXQLWDQGSRVVLEOHLQMXU\
read this manual carefully and follow all installation
instructions. This product has been checked for
proper function prior to shipping and is guaranteed
against manufacturing defects.
Before starting your installation, disconnect
the battery’s negative terminal to prevent
GDPDJHWRWKHXQLW¿UHDQGRUULVNRILQMXU\ For
a proper performance and to ensure full warranty
FRYHUDJHZHVWURQJO\UHFRPPHQGWRJHWWKLVSURG-
uct installed by an authorized HELIX dealer.
Install your HELIX V EIGHT DSP in a dry location
ZLWK VXI¿FLHQW DLU FLUFXODWLRQ IRU SURSHU FRROLQJ RI
WKH HTXLSPHQW 7KH DPSOL¿HU VKRXOG EH VHFXUHG
to a solid mounting surface using proper mount-
LQJ KDUGZDUH %HIRUH PRXQWLQJ FDUHIXOO\ H[DPLQH
the area around and behind the proposed instal-
lation location to insure that there are no electrical
cables or components, hydraulic brake lines or any
part of the fuel tank located behind the mounting
surface. Failure to do so may result in unpredictable
damage to these components and possible costly
UHSDLUVWRWKHYHKLFOH
General instruction for connecting the HELIX
9(,*+7'63DPSOL¿HU
7KH+(/,;9(,*+7'63DPSOL¿HUPD\RQO\EHLQ-
VWDOOHGLQ YHKLFOHVZKLFKKDYHD 9ROWVQHJDWLYH
terminal connected to the chassis ground. Any oth-
HUV\VWHPFRXOGFDXVHGDPDJHWRWKHDPSOL¿HUDQG
WKHHOHFWULFDOV\VWHPRIWKHYHKLFOH
7KHSRVLWLYHFDEOHIURPWKHEDWWHU\IRUWKHFRPSOHWH
V\VWHP VKRXOG EH SURYLGHG ZLWK D PDLQ IXVH DW D
GLVWDQFHRIPD[ FPIURP WKHEDWWHU\7KH YDO-
XHRIWKHIXVHLVFDOFXODWHGIURPWKHPD[LPXPWRWDO
current input of the car audio system.
8VH RQO\ VXLWDEOH FDEOHV ZLWK VXI¿FLHQW FD-
ble cross-section for the connection of HELIX
V EIGHT DSP. The fuses may only be replaced
by identically rated fuses (2 x 30 A) to avoid
GDPDJHRIWKHDPSOL¿HU
Prior to installation, plan the wire routing to
DYRLG DQ\ SRVVLEOH GDPDJH WR WKH ZLUH KDUQHVV
All cabling should be protected against possible
FUXVKLQJ RU SLQFKLQJ KD]DUGV $OVR DYRLG URXWLQJ
cables close to potential noise sources such as
electric motors, high power accessories and other
YHKLFOHKDUQHVVHV
Congratulations!
General instructions