What to do if Henny Penny Fryer vat is under-filled?
If the vat of your Henny Penny Fryer is under-filled, the JIB might be low or empty, so fill the JIB. Alternatively, the JIB oil line may be clogged or collapsed, so check the JIB line. The filter pan may also need cleaning, so clean the filter pan and change the paper or pad.
How to unclog Henny Penny LVE-204 Fryer drain?
If the oil is not draining from the vat of your Henny Penny Fryer, the drain valve may be clogged with crumbs. Open the valve and use a straight white brush to force the crumbs through. Do not leave the brush in the drain valve. Also, the drain trough might be clogged; remove the right side panel, remove the plug from the end of the trough, and clean it.
How to troubleshoot a completely inoperative Henny Penny LVE-204 Fryer?
If the Henny Penny Fryer is completely inoperative when the power switch is in the ON position, here are some things to check: * Ensure the unit is plugged in. * Check the breaker or fuse at the supply box. * Verify the voltage at the wall receptacle. * Inspect the MAIN POWER switch and replace it if it's defective. * Examine the cord and plug. * Reset the circuit breakers in the fryer. * Reset the transformer circuit breaker.
Why is the oil foaming or boiling over in my Henny Penny Fryer?
If the oil in your Henny Penny Fryer is foaming or boiling over, consider the following: * **Water in oil**: At the end of a cook cycle, drain and clean the vat, then add fresh oil. * **Improper or bad oil**: Ensure you're using the recommended oil. * **Improper filtering**: Refer to the oil filtering procedure. * **Cold zone full of crumbs**: Filter the oil. * **Improper rinsing after cleaning**: Thoroughly rinse the vat to remove any cleaning agent.
Why is the filter motor running but pumping oil slowly in my Henny Penny Fryer?
If the filter motor runs but pumps oil slowly in your Henny Penny Fryer, try these solutions: * **Filter line connections loose:** Tighten the filter line connections. * **Drain pan o-rings damaged or missing:** Install new o-rings. * **Filter paper or pad clogged:** Change the filter paper or pad.
What does the “CHANGE FILTER PAD” prompt mean on my Henny Penny LVE-204?
If the “CHANGE FILTER PAD” prompt appears on your Henny Penny Fryer, the following could be the reason: * The pad has not been changed within a 24 hr period, or the main power switch was turned off during filter pad change. Replace the pad with a NEW filter pad with the main power switch on. Note: For 24/7 stores, replace the filter twice a day. * The drain pan microswitch is stuck. Check the microswitch.
What does error code “E-5” mean on my Henny Penny LVE-204 Fryer?
If your Henny Penny Fryer displays “E-5”, the heating circuits and temperature probe should be checked. Turn the switch to the OFF position, then turn it back to ON.
What does error code E-31 mean on my Henny Penny Fryer?
If your Henny Penny Fryer shows a control error code “E-31”, it means the elements are up. Lower the elements back into the vat to resolve this issue.
Why is Henny Penny Fryer filter motor pumping oil slowly?
If the filter motor of your Henny Penny Fryer runs but pumps oil slowly, check for loose filter line connections and tighten them. The filter paper or pad may also be clogged, so try changing it.
Why Henny Penny LVE-204 Fryer filter motor won't run?
If the filter motor on your Henny Penny Fryer is not running, first ensure the power cord for vat #1 is plugged into the receptacle. Also check if the breakers in the fryer have tripped and reset them by opening the left door. If those aren't the issue, the thermal reset button on the rear of the pump motor may be tripped. Allow time for the motor to cool, remove the JIB, and then use a screwdriver to press hard against the button until it clicks.
General| Brand | Henny Penny |
|---|---|
| Model | LVE-204 |
| Category | Fryer |
| Language | English |
To Next Page
