What to do if the weight shown on the Hill-Rom P8010 Medical Equipment scale display is flashing?
To resolve the issue of a Hill-Rom medical equipment scale display showing a flashing weight, calibrate the scale. If the problem persists, replace the scale P.C. board.
Why the Steering Plus™ Steering System Does Not Operate Correctly in Hill-Rom P8010?
If the Steering Plus™ Steering System on your Hill-Rom medical equipment does not operate correctly, examine the fifth wheel pivot arms and pivot bracket for correct assembly. If problems persist, remove the Steering Plus™ Steering System assembly and replace any damaged or inoperative parts, or replace the fifth wheel.
What to do if the siderail on Hill-Rom P8010 Medical Equipment does not operate correctly?
If the siderail on your Hill-Rom medical equipment does not operate correctly, check for any obstructions and remove them. If the problem continues, consider replacing the latch.
What causes loss of corner steer in Hill-Rom Medical Equipment?
To resolve the issue of loss of corner steer in your Hill-Rom medical equipment, try tightening the brake/steer link screw. If this doesn't solve the problem, consider replacing the caster.
Why are there reduced pedal pumps on my Hill-Rom P8010 Medical Equipment?
To address the issue of reduced pedal pumps on your Hill-Rom medical equipment, start by removing air from the hydraulic system. If the head or foot end still doesn't rise, replace the corresponding hydraulic cylinder.
How to fix a push handle malfunction on Hill-Rom P8010?
To fix a push handle malfunction on Hill-Rom medical equipment, first remove any interference that may be obstructing it. If the issue persists, consider replacing the push handle latch or the push handles themselves.
What to do if the Hill-Rom P8010 stretcher will not go into neutral position?
If your Hill-Rom medical equipment stretcher will not go into neutral position, check the brake/steer link at the head and foot ends of the stretcher for correct orientation, and adjust if necessary. Also, inspect each caster and replace any that are defective. You may also need to tighten the brake/steer link screw.
What to do if the weight shown on the Hill-Rom Medical Equipment scale display is not correct?
If the weight shown on the Hill-Rom medical equipment scale display is not correct, ensure all packing materials and shims have been removed before taking a weight reading. Also, verify that the load beam cables are connected in the correct order before taking another reading.
Why is there reduced braking ability in my Hill-Rom P8010 Medical Equipment?
To address reduced braking ability in your Hill-Rom medical equipment, ensure the brake/steer link adjustment at both ends of the stretcher is correct. If necessary, adjust the brake/steer link. If the issue persists, adjust the caster brake shoes or replace any defective casters.
What to do if the Hill-Rom P8010 stretcher will not lower?
If your Hill-Rom medical equipment stretcher will not lower, you can try to adjust the release mechanism. If that doesn't work, you may need to replace the hydraulic cylinder at either the head or foot end of the stretcher.
General| Brand | Hill-Rom |
|---|---|
| Model | P8010 |
| Category | Medical Equipment |
| Language | English |
Details the physical, electrical, and environmental specifications of the stretchers.
Offers critical safety advice for operating and servicing the stretchers to prevent injury or damage.
A table listing common scale display problems and corresponding troubleshooting procedures (RAPs).
Details specific functional checks for various stretcher components to verify proper operation.
Troubleshooting procedure for issues with reduced braking ability on the stretcher.
Procedure to troubleshoot and resolve issues related to the loss of corner steer functionality.
Troubleshooting steps for when the Steering Plus™ Steering System is not functioning correctly.
Guidance for diagnosing and fixing issues where the stretcher does not enter the neutral position.
Troubleshooting steps for issues with reduced pedal pump performance on the stretcher.
Procedure to address problems where the stretcher fails to lower correctly.
Troubleshooting steps for siderails that are not operating correctly.
Troubleshooting for back section articulation issues on specific stretcher models.
Steps to diagnose and resolve malfunctions related to the push handles.
Troubleshooting for the permanent IV pole not raising or lowering correctly.
Troubleshooting steps for knee section articulation issues on specific stretcher models.
Procedure to troubleshoot when the scale display fails to turn on.
Step-by-step instructions for removing and replacing the siderail on specified stretcher models.
Detailed procedure for the removal and replacement of the siderail on the Electric (P8020) Stretcher.
Instructions for removing and replacing the siderail cable assembly and upright tube on the Electric (P8020) Stretcher.
Procedure for removing and replacing the patient control switch on the Electric (P8020) Stretcher.
Steps for removing and replacing the nurse control switch on the Electric (P8020) Stretcher.
Detailed instructions for removing and replacing the control board in the Electric (P8020) Stretcher.
Procedure for removing, replacing, and adjusting the back section gas spring on specific stretcher models.
Instructions for removing, replacing, and adjusting the back section gas spring on the Surgical (P8010) Stretcher.
Procedure for removing, replacing, and adjusting the articulating headrest gas spring on the Surgical (P8010) Stretcher.
Steps for removing, replacing, and adjusting the knee screw assembly on specific stretcher models.
Procedure for removing, replacing, and adjusting the knee drive assembly on the Electric (P8020) Stretcher.
Instructions for removing, replacing, and adjusting the head drive assembly on the Electric (P8020) Stretcher.
Detailed procedure for removing, replacing, and adjusting the CPR release cable assembly.
Procedure for removing and replacing the foot support Mechlok® device on the OB/GYN Stretcher.
Instructions for removing, replacing, and adjusting the foot support gas spring on the OB/GYN Stretcher.
Detailed steps for adjusting the caster brake shoes for proper function.
Instructions on how to adjust the brake/steer pedal linkage for correct operation.
Procedure for removing, replacing, and adjusting the hydraulic cylinder.
Procedure for removing and replacing the load beams for the scale system, including calibration.
Steps for replacing the scale display or the scale P.C. board.
Instructions on how to identify and order replacement parts using part numbers and model information.
Provides a list of recommended spare parts for servicing five or more units.
Parts list and diagram for the head and knee drive assembly of the Electric (P8020) Stretcher.
Parts list and diagram for the head drive and CPR assemblies of the Electric (P8020) Stretcher.
Parts list and diagram for the control board assembly (120V AC and 230V AC) of the Electric (P8020) Stretcher.
Parts list and diagram for the siderail assembly on Procedural and Trauma stretchers.
Parts list and diagram for the siderail assembly on the Surgical (P8010) Stretcher.
Parts list and diagram for the siderail assembly on the Electric (P8020) Stretcher.
Parts list and diagram for the siderail assembly on the OB/GYN (P8050) Stretcher.
Importance and recommendations for establishing an effective preventive maintenance program.
A schedule outlining routine preventive maintenance checks for various stretcher functions.
A checklist designed to maintain a running history of maintenance and repair costs for stretchers.
To Next Page