SPECIFICATION
The Hiretech 8 Multi-Speed Drum Floor SanderHT
will sand hard and soft wood floors, cork and
composition floors that require rapid sanding and
leveling to a fine finish. A powerful motor drives a
finely balanced sanding drum which is covered in a
unique drum rubber providing a high quality finish to
both hard and soft woods and other surfaces.
Completely self contained with a high efficiency dust
pickup the 8 breaks down into three simpleHT
component parts for easy transport. Multi-Speed
control with the choice of four operating speeds, no
volt start and overload protection. The 8 is a highHT
performance floor sander suitable for professional
and homeowner use.
SAFETY
1. For safety it is recommended that a residual
current circuit breaker (ground fault interrupter)
is used with this machine.
2. Check the operating voltage is correct, the
voltage is detailed on the serial plate on the top
of the body of the floor sander.
3. Always completely assemble the floor sander
and connect the handle cable to the body of the
floor sander before connecting to the power
supply.
4. Always disconnect from the power supply when
changing the abrasive paper, servicing the floor
sander, replacing the dust bag or leaving the
machine unattended.
5. Always replace the dust bag (paper type) or
empty the dust bag (cloth type) when the dust in
the bag reaches the ‘ ’ line or when theMAX
machine is left unattended.
6. Never dispose of or empty the contents of the
dust bag into a fire or incinerator.
7. Never reuse the paper dust bag or use a non
standard bag. Cloth bags must be in good
condition with no holes.
8. Always wear a dust mask when using the floor
sander, handling the dust bag or cleaning the
machine after use.
9. Wear ear protection when using the floor sander.
10. Ensure adequate ventilation of the work area to
avoid the formation of a combustible mixture of
flying dust and air.
11. Never smoke when using or servicing the floor
sander or when handling the dust bag.
12. Never expose the machine to rain or damp.
Always store in a dry place.
13. Stop the floor sander immediately if damage to
the machine or abrasive paper is suspected.
14. Never allow the power cable to come into contact
with the sanding drum when the floor sander is in
operation. If the power cable becomes damaged
and the inner conductors are exposed switch the
power and remove the plug beforeOFF
attempting to move the machine. The cable
must be replaced by an authorised dealer or
qualified electrician using Hiretech genuine
spare parts only.
15. Keep hands, feet and loose clothing away from
all moving parts of the machine.
16. Punch down or remove all nails, screws, tacks
and other fixings from the floor before sanding to
prevent contact with the sanding drum.
1
Read the following Safety and Operational
notes before using your Hiretech 8 DrumHT
Floor Sander.
Noise: 95 dBa at 1m etre (3’ 3")
Vibration: 1.60 m /s² r.m.s.
Switch: Electro n ic O n /O ff s w itch a n d
m u lti-s p ee d co n tro l w ith n o
volt start and overload
protection
Motor RPM: M ulti-speed user selected
8,500/7,300/6,900/6,500
Drum RPM: M ulti-speed user selected
3,300/2,800/2,650/2,500
Drive: Non-slip toothed tim ing belts
a n d g e a r cu t p u lleys .
Dust Pickup: Seated oversize vacuum fan
with adjustable dust pan,
disposable paper dust or cloth
bag.
Moving Parts: Sea led fo r life b a ll b e a rin g s.
Guards: H ig h im p a ct in je ctio n m o u ld ed
ABS.
Abrasive: 495m m (19.5") total length x
203m m (8") wide sheet with
notched and angled ends P24
to P120 grit.
Power Cable: 7m (23') Non-marking outer
in su la tio n .
Dimensions
(w ) x (d ) x (h )
322m m x 940m m x 855m m
(12.7" x 37" x 33.6")
Weight Net: 41.5kg (91.5lbs)
Shipping
Weight:
50.0kg (110.3lbs)
Shipping
Dimensions:
78 x 40 x 44cm
(30.75" x 15.75" x 17.5")
W arranty: 2years
Continuous heavy duty AC/DC
s elf co o lin g 4 b ru s h .
203m m (8") wide alum inium
ex tru s io n w ith m o u ld e d ru b b er
drum cover.
Sanding D rum :
Motor:
110/120 V 50/60 Hz
220/240 V 50/60 Hz
110/120 V 8A
220/250 V 5A
Average
Load Current:
110/120 V 15A
220/250 V 8A
Power Supply:
Off Load
Current:
To Next Page
Loading...
