37
CP-WX11000 ( P6WX )
8. Removing the lens (2)
Support the lens and remove the lens from
the LCD projector. Place the detached
lens on a soft cloth or similar.
Caution:
ŷ Do not hold the lens by the lens
shade when removing the lens as this
may lead to injury or malfunction.
ŷ Take care to avoid hitting the surface
of the lens on the LCD projector
when removing the lens as this may
lead to malfunction.
11. Attaching the lens (2)
Support the lens installed in the LCD
projector and move the lock lever on the
projector as far as it will go to the right
(until the lock lever clicks into the locked
position).
After attaching the lens, check that it is
securely mounted and that the lock lever
does not move.
Caution:
ŷ To prevent the lens from falling off, after attaching the lens, check that it is
securely mounted and that the lock lever does not move.
10. Attaching the lens (1)
Follow the procedures in steps 5 and 6 for
Attaching the SD-804/LL-805/UL-806 Lens
and install the lens in the LCD projector.
Support the lens with the lens adapter
attached and install it in the LCD projector.
Caution:
ŷ Do not hold the lens by the lens shade
when attaching the lens as this may
lead to injury or malfunction.
ŷ Take care to avoid hitting the surface of
the lens on the LCD projector when attaching the lens as this may lead to malfunction.
Changing from a USL-801/SL-802/SL-803 Lens to an SD-804/LL-805/UL-806 Lens
1. Removing the optional parts (1)
(SL-802/SL-803 only)
Rotate the protector 90° until the catch is
at the top.
Caution:
ŷ Be sure to turn off the LCD projector
before changing the lens.
ŷ Return the lens shift to the center
position. Refer to the user manual
supplied with the LCD projector for
instructions on how to return the
lens shift to the center position.
2. Removing the optional parts (2)
(SL-802/SL-803 only)
Using a ¿ ne-tipped object or the hexagon
wrench supplied with the LCD projector,
disengage the catch on the protector.
Disengage the catch on the opposite side
in the same way.
3. Removing the optional parts (3)
(SL-802/SL-803 only)
Remove the two protectors.
4. Disassembling the main unit parts
Unscrew the front ring.
Remove the front cover.
5. Removing the optional parts (4)
(SL-802/SL-803 only)
Rotate the blinder 90° until the catch is at
the top.
Disengage the catch on the opposite side
in the same way.
Disengage the catch on the opposite side
in the same way.
6. Removing the optional parts (5)
(SL-802/SL-803 only)
Remove the two blinders.
7. Removing the lens (1)
Support the lens and move the lock lever
to the left while pressing the lock lever
release button on the LCD projector.
9. Removing the lens (3)
Unplug the connector on the lens from
the socket on the lens adapter.
Using the hexagon wrench supplied
with the LCD projector, loosen the four
hexagon screws on the lens and remove
the lens adapter.
Have the replacement USL-801/SL-802/
SL-803 lens ready. Follow the procedures
in steps 1 and 2 for Attaching the SD-804/
LL-805/UL-806 Lens and mount the lens
adapter on the replacement lens.
12. Assembling the main unit parts (1)
Insert the two catches on the front cover
into the LCD projector body to attach the
front cover.
13. Assembling the main unit parts (2)
Have the blind sheet supplied with the
lens ready and mount it on the lens
shade.
Mount the blind sheet with its matte side
facing out.
14. Assembling the main unit parts (3)
Screw on the front ring. Lens
attachment is completed.
Caution:
ŷ Take care not to get the blind sheet
trapped when À tting the front ring
as this may lead to malfunction.
Protector
Hexagon wrench
Catch part
Catch
Protector
Release button
Front cover Front ring
Catch
Catch
Lock lever
Terminal on projector
Groove
Rib
Hexagon wrench
Connector
Socket
Lens shade
Terminal on lens
Lock lever
Lock lever
Front cover
Catch
Catch
Blind sheet
Front ring
Lens shade
Lens shade
To Next Page
Loading...
