Hitachi DK23DA-20F - Page 7

K6602705
Rev.3
08.20.01
- 7 -
6.3.2 Command --------------------------- 35
6.3.2.1 Command Summary --------------------------- 35
6.3.2.2 Command BSY Timing --------------------------- 36
6.3.2.3 PIO Data In Commands --------------------------- 37
6.3.2.3.1 Identify Device [ECh] --------------------------- 38
6.3.2.3.2 Read Buffer [E4h] --------------------------- 45
6.3.2.3.3 Read Sectors [20h, 21h] --------------------------- 45
6.3.2.3.4 Read Long [22h, 23h] --------------------------- 45
6.3.2.3.5 Read Multiple [C4h] --------------------------- 45
6.3.2.4 PIO Data Out Commands --------------------------- 46
6.3.2.4.1 Write Buffer [E8h] --------------------------- 46
6.3.2.4.2 Write Sectors [30h, 31h] --------------------------- 46
6.3.2.4.3 Write Long [32h, 33h] --------------------------- 46
6.3.2.4.4 Write Multiple [C5h] --------------------------- 46
6.3.2.4.5 Format Track [50h] --------------------------- 47
6.3.2.5 Non-Data Commands --------------------------- 47
6.3.2.5.1 Initialize Device Parameters [91h] --------------------------- 47
6.3.2.5.2. Read Verify [40h, 41h] --------------------------- 48
6.3.2.5.3 Recalibrate [1Xh] --------------------------- 48
6.3.2.5.4 Seek [7Xh] --------------------------- 48
6.3.2.5.5 Set Features [EFh] --------------------------- 48
6.3.2.5.6 Set Multiple Mode [C6h] --------------------------- 49
6.3.2.5.7 Execute Device Diagnostic [90h] --------------------------- 49
6.3.2.5.8 Flush Cache [E7h] --------------------------- 50
6.3.2.6 Power Commands --------------------------- 51
6.3.2.6.1 Power Management --------------------------- 51
6.3.2.6.2 Advanced Power Management --------------------------- 52
6.3.2.6.3 Check Power Mode [98h, E5h] --------------------------- 53
6.3.2.6.4 Idle [97h, E3h] --------------------------- 54
6.3.2.6.5 Idle Immediate [95h, E1h] --------------------------- 54
6.3.2.6.6 Sleep [99h, E6h] --------------------------- 54
6.3.2.6.7 Standby [96h, E2h] --------------------------- 54
6.3.2.6.8 Standby Immediate [94h, E0h] --------------------------- 54
6.3.2.7 DMA Data In/Out Commands --------------------------- 55
6.3.2.7.1 Read DMA [C8h, C9h] --------------------------- 55
6.3.2.7.2 Write DMA [CAh, CBh] --------------------------- 55
6.3.2.8 SMART Feature --------------------------- 56
6.3.2.8.1 Attribute Parameters --------------------------- 56
6.2.7.8.2 SMART Device Error Log Reporting --------------------------- 57
6.2.7.8.3 SMART Operation with Management Modes --------------------------- 57
6.3.2.8.4 SMART Function Default Setting --------------------------- 57
6.3.2.8.5 SMART Enable Operations [B0h, Sub D8h] --------------------------- 57
6.3.2.8.6 SMART Disable Operations [B0h, Sub D9h] --------------------------- 58
6.3.2.8.7 SMART Return Status [B0h, Sub DAh] --------------------------- 59
6.3.2.8.8 SMART Enable/Disable Attribute AUTOSAVE [B0h, Sub D2h] ------------------ 59
6.3.2.8.9 SMART Save Attribute Values [B0h, Sub D3h] ----------------------------- 60
6.3.2.8.10 SMART Enable/Disable Automatic Off-line [B0h, Sub DBh] -------------------- 61
6.3.2.8.11 SMART Execute Off-line Immediate [B0h, Sub D4h] --------------------------- 62