To Next PageTo Next Page
Need help?Do you have a question about the Hitachi F350 and is the answer not in the manual?
Identifies the target readers for this hardware reference guide, including administrators and service providers.
Explains the typographic and iconographic conventions used throughout the document for clarity and consistency.
Provides contact information and resources for technical support and community engagement with Hitachi Vantara.
Describes the system's block-level storage architecture, including controller chassis and drive trays.
Highlights key attributes of the storage system, such as high performance, reliability, and scalability.
Details the controller chassis with small form-factor drive bays (CBSS), including its components and specifications.
Explains the front and rear panel LEDs on the CBSS controller chassis for monitoring operational status.
Introduces front-end modules (FEMs) or channel boards, detailing their function and interface types like iSCSI and Fibre Channel.
Describes back-end modules (BEMs) or disk boards that control data transfer between drives and cache memory.
Details the physical specifications of the small form-factor drive tray (DBS/DBSE), including dimensions and drive slots.
Describes the front and rear panels of the SFF drive tray, including LEDs and lock mechanisms.
Explains the AC power supply units used in drive trays, including their LEDs and connector functions.
Provides a step-by-step procedure for safely powering down the storage system using the main switch.
Covers the treatment, lifetime, and replacement considerations for the system's battery unit.
Lists the standard and optional controller and drive tray components for the VSP F350 model.
Lists the standard and optional controller and drive tray components for the VSP F370 model.
Provides a list of available data and power cables, including specifications for SAS and optical cables.
Details the physical dimensions, weight, heat output, and power consumption for VSP F350 components.
Details the physical dimensions, weight, heat output, and power consumption for VSP F370 components.
Outlines the electrical input power requirements, including voltage, frequency, and current ratings for controllers and drive trays.
Covers environmental operating conditions such as temperature, humidity, vibration, impact, and altitude.
Specifies the operating and non-operating temperature and humidity ranges for the storage system.
Defines acceptable vibration, impact, and altitude levels for reliable storage system operation.
Describes the acoustic noise levels generated by the system during operation and non-operation.
Explains how shared memory capacity affects software features like replication, provisioning, and tiering.
Lists the TCP/IP ports required for system management, communication, and network services.
Details how controllers connect to optional SVPs, drive trays, and other devices via various ports.
Describes the physical connectivity requirements for the Service Processor (SVP), including network setup.
Lists the types of cables required for storage system installation, including Fibre Channel, iSCSI, and SAS.
Provides specifications for Fibre Channel cables, including data transfer rates, lengths, and connector types.
Details specifications for iSCSI cables, covering optical and copper interfaces, lengths, and connectors.
Lists the networking standards and protocols that apply to iSCSI ports for management and data transfer.
Offers guidelines for organizing cables to ensure proper airflow, protect connections, and facilitate maintenance.
Explains AC power cable standards, types, and assemblies, including connector and receptacle information.
Details specifications for Americas single-phase Power Distribution Units (PDUs), including part numbers and capacity.
Details specifications for Americas three-phase Power Distribution Units (PDUs), including part numbers and capacity.
Details specifications for APAC and EMEA single-phase Power Distribution Units (PDUs), including part numbers and capacity.
Details specifications for APAC and EMEA three-phase Power Distribution Units (PDUs), including part numbers and capacity.
Details specifications for three-phase PDUs used across Americas, APAC, and EMEA regions, including part numbers and capacity.
Provides requirements and guidelines for installing storage systems in non-Hitachi racks.
Lists the rail kit information for mounting storage systems in Hitachi Universal V2 Racks.
Explains the meaning of various warning symbols found on storage system hardware components.
Illustrates and explains specific warning labels located on the CBSS controller hardware.
Illustrates and explains specific warning labels located on the CBSL controller hardware.
Shows warning labels for small form factor drive trays and the system's battery unit.
Provides guidance on the proper disposal and recycling of electrical equipment and cache backup batteries.
Lists tested and certified standards for electronic emission controls, certifications, and radio interference.
Covers FDA radiation performance standards and FCC regulations regarding electromagnetic interference (EMI).
General