EasyManua.ls Logo

Hitachi HTS541616J9SA00 - Figure 21 Command Set - Continued

Hitachi HTS541616J9SA00
167 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
Travelstar 5K160 (SATA) Hard Disk Drive Specification
70/167
Code Protocol Command
(Hex) 7 6 5 4 3 2 1 0
3 Set Max Address F9 1 1 1 1 1 0 0 1
3 Set Max Address Ext 37 0 0 1 1 0 1 1 1
3 Set Max Freeze Lock F9 1 1 1 1 1 0 0 1
3 Set Max Lock F9 1 1 1 1 1 0 0 1
2 Set Max Set Password F9 1 1 1 1 1 0 0 1
2 Set Max Unlock F9 1 1 1 1 1 0 0 1
3 Set Multiple Mode C6 1 1 0 0 0 1 1 0
3 Sleep E6 1 1 1 0 0 1 1 0
3 Sleep* 99 1 0 0 1 1 0 0 1
3 S.M.A.R.T. Disable Operations B0 1 0 1 1 0 0 0 0
3 S.M.A.R.T. Enable/Disable Attribute Auto save B0 1 0 1 1 0 0 0 0
3 S.M.A.R.T. Enable/Disable Automatic Off-line B0 1 0 1 1 0 0 0 0
3 S.M.A.R.T. Enable Operations B0 1 0 1 1 0 0 0 0
3 S.M.A.R.T. Execute Off-line Immediate B0 1 0 1 1 0 0 0 0
1 S.M.A.R.T. Read Attribute Values B0 1 0 1 1 0 0 0 0
1 S.M.A.R.T. Read Attribute Thresholds B0 1 0 1 1 0 0 0 0
1 S.M.A.R.T. Read Log Sector B0 1 0 1 1 0 0 0 0
3 S.M.A.R.T. Return Status B0 1 0 1 1 0 0 0 0
3 S.M.A.R.T. Save Attribute Values B0 1 0 1 1 0 0 0 0
2 S.M.A.R.T. Write Log Sector B0 1 0 1 1 0 0 0 0
3 Standby E2 1 1 1 0 0 0 1 0
3 Standby* 96 1 0 0 1 0 1 1 0
3 Standby Immediate E0 1 1 1 0 0 0 0 0
3 Standby Immediate* 94 1 0 0 1 0 1 0 0
2 Write Buffer E8 1 1 1 0 1 0 0 0
4 Write DMA CA 1 1 0 0 1 0 1 0
4 Write DMA CB 1 1 0 0 1 0 1 1
4 Write DMA Ext 35 0 0 1 1 0 1 0 1
4 Write DMA FUA Ext 3D 0 0 1 1 1 1 0 1
5 Write FPDMA Queued 61 0 1 1 0 0 0 0 1
2 Write Log Ext 3F 0 0 1 1 1 1 1 1
2 Write Long 32 0 0 1 1 0 0 1 0
2 Write Long 33 0 0 1 1 0 0 1 1
2 Write Multiple C5 1 1 0 0 0 1 0 1
2 Write Multiple Ext 39 0 0 1 1 1 0 0 1
2 Write Multiple FUA Ext CE 1 1 0 0 1 1 1 0
2 Write Sector(s) 30 0 0 1 1 0 0 0 0
2 Write Sector(s) 31 0 0 1 1 0 0 0 1
2 Write Sector(s) Ext 34 0 0 1 1 0 1 0 0
Protocol : 1 : PIO data IN command
2 : PIO data OUT command
3 : Non data command
4 : DMA command
5 : First-parity DMA command
+ : Vendor specific command
Figure 21 Command Set - continued
Commands marked * are alternate command codes for previously defined commands.

Table of Contents

Related product manuals