To Next Page
D
dedwardsAug 20, 2025
What to do if my Hitachi Nail Gun output is decreased and it generates heat?
- WWendy WatsonAug 21, 2025
To resolve decreased output and overheating in your Hitachi Nail Gun, clean the Filter Mesh [2].
What to do if my Hitachi Nail Gun output is decreased and it generates heat?
To resolve decreased output and overheating in your Hitachi Nail Gun, clean the Filter Mesh [2].
Why my Hitachi NT 65GB Nail Gun does not start?
To fix a Hitachi Nail Gun that isn't starting, ensure the Battery [58] is correctly set in the nailer.
What to do if my Hitachi NT 65GB fuel is not sprayed?
If your Hitachi Nail Gun isn't spraying fuel, replace the fuel cell with a new one.
Why is my Hitachi Nail Gun overheated?
If your Hitachi Nail Gun is overheating, clean the Filter Mesh [2]. Also, avoid using the nailer at high speed (1 nail/sec) or for continuous operation exceeding 1,000 nails/h.
What to do if no nail is driven in my Hitachi NT 65GB Nail Gun?
If no nail is driven though nails are set properly and combustion is normal in your Hitachi Nail Gun, return the Piston [27] to the uppermost position with a flat-blade screwdriver. Hold down Pushing Lever (A) [82] securely until nailing operation is completed. Consider replacing Piston Ring (B) [17], the Reed Valve [50], cleaning inside the cylinder, or replacing Piston Ring (A) [26].
Why is the output of my Hitachi NT 65GB low?
To resolve decreased output in your Hitachi Nail Gun, clean the Filter Mesh [2]. Also, ensure the outside air temperature is between 0°C to 40°C and the altitude is less than 1,500 m (5,000 feet).
What to do if the number of revolutions of the Fan [11] is low in Hitachi NT 65GB?
If the number of revolutions of the Fan [11] is low, charge the Battery [58].
Why is there abnormal noise during fan rotation in my Hitachi NT 65GB?
To address abnormal noise during fan rotation in your Hitachi Nail Gun, mount each part properly.
What to do if Hitachi NT 65GB sprays fuel but no combustion occurs because of high temperature?
If your Hitachi Nail Gun sprays fuel but no combustion occurs and the nailer is left under a high temperature condition, allow the main body and fuel cell to cool down. You may also need to replace the fuel cell with a new one.
What to do if my Hitachi Nail Gun sprays fuel but no combustion occurs, and the bag in the fuel cell is damaged?
If your Hitachi Nail Gun sprays fuel but no combustion occurs due to a damaged bag in the fuel cell, replace the fuel cell with a new one.
Identifies the Hitachi 65 mm (2-1/2") Gas Finish Nailer, Model NT 65GB.
Details the strategy to enter the finish nailer market with Model NT 65GB.
Lists primary uses for framing and cabinet assembly.
Highlights key features like lightweight design, comfortable grip, and ease of use.
Details the technical specifications of the NT 65GB gas finish nailer.
Explains the full sequential actuation mechanism of the nailer.
Specifies applicable T-shaped finish nails for the NT 65GB model.
Discusses output energy range and environmental factors affecting it.
Provides general and specific precautions for safe and efficient tool use.
Lists basic safety precautions to be understood before tool use.
Outlines relevant safety regulations for the USA and Europe.
Describes the construction and main sections of the gas nailer.
Explains the step-by-step process of how the nailer drives nails.
Details the operation of the full sequential action mechanism for safety.
Lists common issues from incorrect operation and their solutions.
Provides guidance for resolving mechanical and electrical issues in gas nailers.
Addresses issues related to sparking and no combustion, offering specific checks.
Explains the correct procedure for grinding the driver blade for optimal performance.
Outlines essential steps and cautions before disassembling or reassembling the tool.
Details how to safely disconnect and reconnect wiring between tool sections.
Provides instructions for disassembling and reassembling the cylinder head section.
Guides users through the disassembly and reassembly of the housing section.
Explains the process for disassembling and reassembling the handle section.
General
