Chapter 8 List of Data Settings
8 - 9
Code Function name Monitored data or setting Default
Setting
during
operation
(allowed or
not)
Change
during
operation
(allowed or
not)
Page
C001 Terminal [1] function (*2)
18
(*2)
¯ {
C002 Terminal [2] function 16
¯ {
C003 Terminal [3] function (*2)
06
(*2)
¯ {
C004 Terminal [4] function 11
¯ {
C005 Terminal [5] function 09
¯ {
C006 Terminal [6] function 6
¯ {
C007 Terminal [7] function 11
¯ {
C008 Terminal [8] function
01 (RV: Reverse RUN), 02 (CF1: Multispeed 1 setting), 03 (CF2: Multispeed 2 setting),
04 (CF3: Multispeed 3 setting), 05 (CF4: Multispeed 4 setting), 06 (JG: Jogging), 07
(DB: external DC braking), 08 (SET: Set 2nd motor data), 09 (2CH: 2-stage
acceleration/deceleration), 11 (FRS: free-run stop), 12 (EXT: external trip), 13 (USP:
unattended start protection), 14: (CS: commercial power source enable), 15 (SFT:
software lock), 16 (AT: analog input voltage/current select), 17 (SET3: 3rd motor
control), 18 (RS: reset), 20 (STA: starting by 3-wire input), 21 (STP: stopping by 3-wire
input), 22 (F/R: forward/reverse switching by 3-wire input), 23 (PID: PID disable), 24
(PIDC: PID reset), 26 (CAS: control gain setting), 27 (UP: remote control UP function),
28 (DWN: remote control DOWN function), 29 (DWN: remote control data clearing), 31
(OPE: forcible operation), 32 (SF1: multispeed bit 1), 33 (SF2: multispeed bit 2), 34
(SF3: multispeed bit 3), 35 (SF4: multispeed bit 4), 36 (SF5: multispeed bit 5), 37 (SF6:
multispeed bit 6), 38 (SF7: multispeed bit 7), 39 (OLR: overload restriction selection), 40
(TL: torque limit enable), 41 (TRQ1: torque limit selection bit 1), 42 (TRQ2: torque limit
selection bit 2), 43 (PPI: P/PI mode selection), 44 (BOK: braking confirmation), 45 (ORT:
orientation), 46 (LAC: LAD cancellation), 47 (PCLR: clearance of position deviation), 48
(STAT: pulse train position command input enable), 50 (ADD: trigger for frequency
addition [A145]), 51 (F-TM: forcible-terminal operation), 52 (ATR: permission of torque
command input), 53 (KHC: cumulative power clearance), 54 (SON: servo-on), 55 (FOC:
forcing), 56 (MI1: general-purpose input 1), 57 (MI2: general-purpose input 2), 58 (MI3:
general-purpose input 3), 59 (MI4: general-purpose input 4), 60 (MI5: general-purpose
input 5), 61 (MI6: general-purpose input 6), 62 (MI7: general-purpose input 7), 63 (MI8:
general-purpose input 8), 65 (AHD: analog command holding), 66 (CP1: multistage
position settings selection 1 ), 67 (CP2: multistage position settings selection 2), 68
(CP3: multistage position settings selection 3), 69 (ORL: Zero-return limit function), 70
(ORG: Zero-return trigger function), 71 (FOT: forward drive stop), 72 (ROT: reverse drive
stop), 73 (SPD: speed / position switching), 74 (PCNT: pulse counter), 75 (PCC: pulse
counter clear), no (NO: no assignment)
9
¯ {
4-46
C011 Terminal [1] active state 00 (NO) / 01 (NC) 00
¯ {
C012 Terminal [2] active state 00 (NO) / 01 (NC) 00
¯ {
C013 Terminal [3] active state 00 (NO) / 01 (NC) 00
¯ {
C014 Terminal [4] active state 00 (NO) / 01 (NC) 00
¯ {
C015 Terminal [5] active state 00 (NO) / 01 (NC) 00
¯ {
C016 Terminal [6] active state 00 (NO) / 01 (NC) 00
¯ {
C017 Terminal [7] active state 00 (NO) / 01 (NC) 00
¯ {
C018 Terminal [8] active state 00 (NO) / 01 (NC) 00
¯ {
Intelligent input terminals
C019 Terminal [FW] active state 00 (NO) / 01 (NC) 00
¯ {
4-47
*2 When the emergency stop function is enabled (SW1 = ON), "18" (RS) and "64" (EMR) are forcibly written to parameters "C001" and "C003", respectively. (You cannot arbitrarily write "64" to
"C001".) If the SW1 signal is turned off and then turned on, "no" (no assignment) is set in parameter "C003".
To Next Page
Loading...
