Chapter 8 List of Data Settings
8 - 10
Code Function name Monitored data or setting Default
Setting
during
operation
(allowed or
not)
Change
during
operation
(allowed or
not)
Page
C021 Terminal [11] function 01
¯ {
C022 Terminal [12] function 00
¯ {
C023 Terminal [13] function 03
¯ {
C024 Terminal [14] function 07
¯ {
C025 Terminal [15] function 40
¯ {
Intelligent output terminals
C026 Alarm relay terminal function
00 (RUN: running), 01 (FA1: constant-speed reached), 02 (FA2: set frequency
overreached), 03 (OL: overload notice advance signal (1)), 04 (OD: output
deviation for PID control), 05 (AL: alarm signal), 06 (FA3: set frequency reached),
07 (OTQ: over-torque), 08 (IP: instantaneous power failure), 09 (UV:
undervoltage), 10 (TRQ: torque limited), 11 (RNT: operation time over), 12 (ONT:
plug-in time over), 13 (THM: thermal alarm signal), 19 (BRK: brake release), 20
(BER: braking error), 21 (ZS: 0 Hz detection signal), 22 (DSE: speed deviation
maximum), 23 (POK: positioning completed), 24 (FA4: set frequency overreached
2), 25 (FA5: set frequency reached 2), 26 (OL2: overload notice advance signal
(2)), 27 (Odc: Analog O disconnection detection), 28 (OIDc: Analog OI
disconnection detection), 29 (O2Dc: Analog O2 disconnection detection), 31
(FBV: PID feedback comparison), 32 (NDc: communication line disconnection),
33 (LOG1: logical operation result 1), 34 (LOG2: logical operation result 2), 35
(LOG3: logical operation result 3), 36 (LOG4: logical operation result 4), 37
(LOG5: logical operation result 5), 38 (LOG6: logical operation result 6), 39
(WAC: capacitor life warning), 40 (WAF: cooling-fan speed drop), 41 (FR: starting
contact signal), 42 (OHF: heat sink overheat warning), 43 (LOC: low-current
indication signal), 44 (M01: general-purpose output 1), 45 (M02: general-purpose
output 2), 46 (M03: general-purpose output 3), 47 (M04: general-purpose output
4), 48 (M05: general-purpose output 5), 49 (M06: general-purpose output 6), 50
(IRDY: inverter ready), 51 (FWR: forward rotation), 52 (RVR: reverse rotation), 53
(MJA: major failure), 54(WCO: window comparator O), 55(WCOI: window
comparator OI), 56 (WCO2: window comparator O2)
(When alarm code output is selected for "C062", functions "AC0" to "AC2" or
"AC0" to "AC3" [ACn: alarm code output] are forcibly assigned to intelligent output
terminals 11 to 13 or 11 to 14, respectively.)
05
¯ {
4-60
C027 [FM] siginal selection
00 (output frequency), 01 (output current), 02 (output torque), 03 (digital output
frequency), 04 (output voltage), 05 (input power), 06 (electronic thermal
overload), 07 (LAD frequency), 08 (digital current monitoring), 09 (motor
temperature), 10 (heat sink temperature), 12 (general-purpose output YA0)
00
¯ {
4-73
C028 [AM] siginal selection
00 (output frequency), 01 (output current), 02 (output torque), 04 (output voltage),
05 (input power), 06 (electronic thermal overload), 07 (LAD frequency), 09 (motor
temperature), 10 (heat sink temperature), 11 (output torque [signed value]), 13
(general-purpose output YA1)
00
¯ {
C029 [AMI] siginal selection
00 (output frequency), 01 (output current), 02 (output torque), 04 (output voltage),
05 (input power), 06 (electronic thermal overload), 07 (LAD frequency), 09 (motor
temperature), 10 (heat sink temperature), 14 (general-purpose output YA2)
00
¯ {
4-74
Analog monitoring
C030
Digital current monitor reference
value
0.20 x "rated current" to 1.50 x "rated current" (A)
Rated
current of
inverter
{ {
4-73
C031 Terminal [11] active state 00 (NO) / 01 (NC) 00
¯ {
C032 Terminal [12] active state 00 (NO) / 01 (NC) 00
¯ {
C033 Terminal [13] active state 00 (NO) / 01 (NC) 00
¯ {
C034 Terminal [14] active state 00 (NO) / 01 (NC) 00
¯ {
C035 Terminal [15] active state 00 (NO) / 01 (NC) 00
¯ {
Intelligent output
terminals
C036 Alarm relay active state 00 (NO) / 01 (NC) 01
¯ {
4-61
To Next Page
Loading...
