8
2. Press the primer bulb approximately 10 times.
3. Ensure the choke lever is set to Run position .
4. Hold down the throttle lock out button and squeeze
and hold in the throttle trigger. Holding in the trigger
is “wide open throttle” (WOT). With wide open throttle,
pull the starter grip with a quick, rm and consistent
upward motion until the engine starts (No more than
6 pulls).
NOTE: If engine does not start (after 6 pulls with the
choke lever in the Run position), return to step 3 under
"TO START A COLD ENGINE" instructions, and repeat
the steps.
5. With choke lever in the Run position , run the
engine with wide open throttle for 10 seconds prior to
operation.
STOPPING THE PRODUCT
See gure 4c.
■ Release the throttle trigger.
■ Hold down the engine switch to the "O" (OFF) position.
OPERATING THE TRIMMER
See gure 5.
Follow these steps to operate the curved shaft trimmer.
■ Start the trimmer.
■ Hold the trimmer at waist level with your right hand
on the trigger handle and your left hand on the front
handle.
■ Place the product on the right side of your body with
the engine behind and away from your body.
■ Trim grass and weeds with the line parallel to the
ground.
WARNING
Injuries may be caused, or aggravated, by prolonged
use of a tool. When using any tool prolonged periods,
ensure you take regular breaks.
ALWAYS OPERATE TRIMMER AT FULL THROTTLE.
Cut tall grass from the top down. This will prevent grass
from wrapping around the shaft ho
using and PRO-CUT I head, which may cause damage
from overheating. If grass becomes wrapped around the
PRO-CUT I head, stop the engine, disconnect the spark
plug wire, and remove the grass. Prolonged cutting at
partial throttle will result in oil dripping from the silencer.
MAINTENANCE
WARNING
When servicing, use only original manufacturer's
replacement parts. Use of any other parts may create a
hazard or cause product damage.
WARNING
Always wear safety goggles or safety glasses with side
shields during product operation. If operation is dusty,
also wear a dust mask.
WARNING
Before inspecting, cleaning, or servicing the machine,
shut off engine, wait for all moving parts to stop, and
disconnect spark plug lead and move it away from
spark plug. Failure to follow these instructions can
result in serious personal injury or property damage.
WARNING
Neglected or poorly conducted maintenance may
create additional hazards. Do not attempt to repair or
maintain this product if you are not qualied to do so.
If in doubt, return to a service centre for professional
assistance.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, lubricant, grease.
WARNING
Do not at any time let brake uids, petrol, petroleum-
based products, penetrating lubricants, etc., come
in contact with plastic parts. Chemicals can damage,
weaken, or destroy plastic, which may result in serious
personal injury.
You can often make adjustments and repairs described in
this manual. For other repairs, have the trimmer serviced
by a service dealer.
LINE REPLACEMENT
See gure 6.
1. Take one 500 mm length of 2.4 mm diameter
monolament pre-cut line.
2. Place the middle of the line under the hook/notch
inside the spool.
3. Feed the ends of the line through the eyelets on the
side of the PRO-CUT I xed line head.
4. Pull the line outwards so it is tight and even on both
sides of the spool.
CLEANING THE AIR FILTER
See gure 7.
A dirty air lter will cause starting difculty, loss of
performance, and shorten the life span of the engine.
Check the air lter monthly. For best performance, replace
the air lter at least once a year.
To Next Page
Loading...
Need help?
General
