Honeywell CIU 888 User Manual (English)

Other manuals for Honeywell CIU 888

Configuration Manual244 pages

Introduction Guide30 pages

Migration Manual110 pages

Sealing Guide20 pages

Protocol Manual44 pages

Installation Guide37 pages

Firmware Upgrade Manual42 pages

Questions and Answers:

O
oblackSep 13, 2025
Why are flexconn commands not working after NOVRam reset on Honeywell Gateway?
- A
  Anthony West MDSep 13, 2025
  After a NOVRam reset, if the flexconn commands are not working for a particular flexline radar gauge, it means that the FlexConn address is wrongly configured for radar gauges in CIU 888. To resolve this: 1. Change the flexconn address using SmartView. 2. If the configuration has 8xx gauge type, change the gauge type to 990 and assign a non-used flexconn address. Then, revert the gauge type back to 8xx gauge type.
T
Tracy SmithAug 25, 2025
Why I am unable to perform manual switchover via Entis Pro on Honeywell Gateway?
- L
  Lisa ArmstrongAug 25, 2025
  If you are unable to perform a manual switchover via Entis Pro, there are a couple of potential causes: * The Sync Link cable between the CIU 888s might be disconnected. In this case, reconnect the Sync Link cable, wait for the initial synchronization to complete, and check the CIU 888 Web interface for an event log indicating that the system is ready for switchover. Then, try the manual switchover again via Entis Pro. * The CIU 888s in the redundant system setup might not be fully synchronized. Try restarting the secondary CIU 888.
S
Scott MitchellAug 25, 2025
How to fix 'Active session exists' message when uploading site configuration to Honeywell Gateway CIU 888?
- A
  Alicia AllenAug 26, 2025
  If you receive an “Active session exists” message when uploading a site configuration to CIU 888 using the Service tool or Migration tool, it means that you are already logged on to CIU 888. To resolve this, close any existing session with CIU 888 before uploading the site configuration again.
R
randy86Aug 26, 2025
What to do if I get 'Cannot connect to remote server' message when uploading site configuration to Honeywell Gateway CIU 888?
- J
  Jennifer VillanuevaAug 26, 2025
  If you encounter the message “Cannot connect to remote server” when uploading a site configuration to the CIU 888 using the Service tool or Migration tool, it indicates that the cable used for connecting your PC/laptop to the Service port/VPN port of CIU 888 is not connected properly. Ensure that the cable is securely connected to the Service/VPN port of CIU 888.
S
Scott JonesSep 14, 2025
Why is there a diagnostics difference in LCD and Web Interface for TRL/2 Field port on Honeywell Gateway?
- D
  Dylan CookSep 14, 2025
  If there's a diagnostics difference in the LCD and Web Interface for the TRL/2 Field port, it indicates improper configuration of TRL/2 data input. Check that the device slave ID is configured correctly in the TRL/2 data input under the Field port and configure it properly.
N
Nancy DukeSep 7, 2025
Why doesn't density dip work with default timeout on Honeywell Gateway?
- M
  Matthew FarrellSep 7, 2025
  If the density dip is not working when the Field port has the default timeout configured (250ms), it's because the density dip command is being aborted due to timeouts on the 1200 baud rate BPM lines. To resolve this, increase the field port timeout to 300-350 ms.
H
Holly BanksSep 8, 2025
What to do if Change Password option doesn't appear when resetting Honeywell Gateway?
- R
  Robert HolmesSep 8, 2025
  If the Change Password option does not appear while resetting the factory settings, this could be due to a power disruption during the factory reset. The factory reset must be re-done, ensuring that the Change Password option is displayed this time.
A
alejandro09Sep 2, 2025
Why are level and pressure values scaled up incorrectly from Honeywell Gateway CIU 888?
- B
  brent07Sep 2, 2025
  If the level value in mm and pressure value in Kgf/cm2 are scaled up and shown incorrectly from CIU 888, it indicates that the Modbus scaling factor for these parameters was increased during database configuration. To fix this, reset the scaling factors for these entities on the host ports using Ensite Pro.
J
John RiceAug 31, 2025
Why is the Honeywell Gateway CIU 888 ring of light orange?
- A
  ahardinAug 31, 2025
  If the CIU System Status or Ring of light is orange, this indicates a warning that the compact flash data free space is less than the required limit (below 300MBs). To resolve this, clear the log files by accessing the CIU 888 web interface (https:// 192.168.1.1), entering your credentials, clicking 'clear logs', and then restarting the CIU 888.
W
William CrawfordSep 1, 2025
What causes site scan timeouts from Engauge with Honeywell Gateway?
- D
  davisjasonSep 1, 2025
  If the site scan from Engauge is timing out, it means the CIU888 is unable to complete the site scan within the Engauge time limits. To address this: 1. Increase the Engauge timeout from 1500-9999 ms based on CIU 888 configuration. 2. Configure CIU888’s field port retries to 1 (minimum supported in Ensite Pro). 3. Disable downlink CIU scan in Engauge. Create the downlink CIUs and their associated gauges manually in Engauge (as we do in case of CIU880). 4. Configure CIU888’s Field port timeout as 1500 ms (as we do in case of CIU880).