Why is the Honeywell Gateway CIU 888 ring of light orange?
If the CIU System Status or Ring of light is orange, this indicates a warning that the compact flash data free space is less than the required limit (below 300MBs). To resolve this, clear the log files by accessing the CIU 888 web interface (https:// 192.168.1.1), entering your credentials, clicking 'clear logs', and then restarting the CIU 888.
How to solve “CIU 888 should be configured before updating INI files” message on Honeywell Gateway?
If you receive the message “CIU 888 should be configured before updating INI files” when updating INI files using the Service tool or Migration tool, it indicates that the CIU 888 has not been fully configured and may be in a factory reset condition. To resolve this, re-upload the site configuration to CIU 888 using the Migration tool, and then update the INI files using the Migration tool.
Why can't I log in to the Honeywell Gateway CIU 888 Web interface after commissioning?
If you are unable to log in to the CIU 888 Web interface of the secondary CIU 888 with your configured password after commissioning a redundant system setup, it's likely because a Reset to Factory settings operation was performed during commissioning. This resets the password to the factory default. To resolve this, log in to the CIU 888 Web interface using the factory default password and change the password when prompted by the system.
Why doesn't the secondary Honeywell Gateway CIU 888 assume secondary role during commissioning?
During the commissioning of a redundant system setup, if the secondary CIU 888 does not assume the secondary role, it could be due to the following reasons: * The Sync Link cable between the CIU 888s is disconnected. This can be observed in the Logs window and Diagnostics window of the CIU 888 Web interface. Reconnect the Sync Link cable between the CIU 888s. * The Configuration lock key switch and/or W&M lock key switch of the primary and/or secondary CIU 888 in the redundant system setup is/are in the ‘closed’ position. Open the Configuration lock key switch and W&M lock key switch of both the primary and secondary CIU 888. Then, perform the procedure for commissioning the redundant system setup.
What to do if secondary Honeywell Gateway CIU 888 is not able to assume primary or secondary role after restart?
If the secondary CIU 888 in a redundant system setup is unable to assume either the primary or secondary role after a restart, it is possible that the Sync Link cable between the CIU 888s is disconnected. To resolve this, reconnect the Sync Link cable between the CIU 888s and then restart the secondary CIU 888.
Why is the Honeywell Gateway CIU 888 status striked out in Entis Pro Hot Standby?
If the CIU 888 status is striked out in the Hot Standby status of Entis Pro, it could be due to these reasons: * The serial cable between the Entis Pro system and CIU 888 is disconnected or malfunctioning. Reconnect the serial cable. If the cable is faulty, replace it. * There is a mismatch between Tank and CIU 888 CRCs within CIU 888 due to database corruption. This can be observed in the Logs window of the CIU 888 Web interface, and the ring of light may be red. In this case, perform a Reset to Factory Settings operation via the CIU 888 display and upload a new site configuration to CIU 888 using the Service tool/ Migration tool.
What to do if I get 'Cannot connect to remote server' message when uploading site configuration to Honeywell Gateway CIU 888?
If you encounter the message “Cannot connect to remote server” when uploading a site configuration to the CIU 888 using the Service tool or Migration tool, it indicates that the cable used for connecting your PC/laptop to the Service port/VPN port of CIU 888 is not connected properly. Ensure that the cable is securely connected to the Service/VPN port of CIU 888.
How to fix 'Active session exists' message when uploading site configuration to Honeywell Gateway CIU 888?
If you receive an “Active session exists” message when uploading a site configuration to CIU 888 using the Service tool or Migration tool, it means that you are already logged on to CIU 888. To resolve this, close any existing session with CIU 888 before uploading the site configuration again.
Why I am unable to perform manual switchover via Entis Pro on Honeywell Gateway?
If you are unable to perform a manual switchover via Entis Pro, there are a couple of potential causes: * The Sync Link cable between the CIU 888s might be disconnected. In this case, reconnect the Sync Link cable, wait for the initial synchronization to complete, and check the CIU 888 Web interface for an event log indicating that the system is ready for switchover. Then, try the manual switchover again via Entis Pro. * The CIU 888s in the redundant system setup might not be fully synchronized. Try restarting the secondary CIU 888.
General| Brand | Honeywell |
|---|---|
| Model | CIU 888 |
| Category | Recording Equipment |
| Language | English |
To Next Page