EasyManua.ls Logo

Honeywell Notifier NFS2-640 - Page 29

Honeywell Notifier NFS2-640
42 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
NFS2-640 UL Listing Document — P/N 52741LD:H9 5/19/2022 29
SUP.T(LASER)
1,2
supervisory N lights supervisory LED Laser smoke detector used to report supervisory
condition rather than alarm. Tracking.
SMOKE(DUCTL) fire alarm Y lights fire alarm LED and activates CBE Duct Laser smoke detector
SUP T(DUCTL) supervisory N lights supervisory LED Laser smoke detector used as a duct detector to
report supervisory condition rather than alarm.
Tracking.
SUP L(DUCTL) supervisory Y lights supervisory LED Laser smoke detector used as a duct detector to
report supervisory condition rather than alarm.
Latching.
AIR REF fire alarm Y lights fire alarm LED and activates CBE Assign to one or more FSL-751 detectors used to
monitor the quality of air entering the protected area.
The air quality measurement allows the VIEW
®
system to compensate for vehicle fumes, fog, or other
particles brought into the protected area through the
ventilation system. Poor air quality will lower the
sensitivity of all FSL-751 detectors on the SLC. The
detector sensitivity, however, remains within approved
limits (always less than 1% obscuration per foot).
Note: A reference detector still functions as a smoke detector, but you should set the detector sensitivity level to the least sensitive level—AL:9 and
PA:9 Change Alarm and Pre-Alarm sensitivity. Refer to “Detector Sensitivity (in percent obscuration per foot)” on page 26 for a complete list of
detector sensitivity settings.
HEAT fire alarm Y lights fire alarm LED and activates CBE 190
o
F intelligent thermal sensor
HEAT+ fire alarm Y lights fire alarm LED and activates CBE 190
o
F intelligent thermal sensor with low temperature
warning.
HEAT(FIXED) fire alarm Y lights fire alarm LED and activates CBE 135
o
F intelligent thermal sensor
HEAT (ROR) fire alarm Y lights fire alarm LED and activates CBE 15
o
F per minute rate-of-rise detector
SMOKE ACCLIM fire alarm Y lights fire alarm LED and activates CBE Combination Photoelectric/heat detector without
freeze warning (Acclimate Plus)
SMOKE(ACCLI+) fire alarm Y lights fire alarm LED and activates CBE Combination Photoelectric/heat detector with freeze
warning (Acclimate Plus, or IntelliQuad FSC-851
Photoelectric Multi-Criteria Smoke Sensor)
SMOKE(MULTI)
3
fire alarm Y lights fire alarm LED and activates CBE Multi-sensor smoke detector
ASPIRATION fire alarm Y lights fire alarm LED and activates CBE Aspiration smoke detector
ASPIR (SUP) supervisory Y lights supervisory LED and activates CBE Aspiration detector supervision
ASPIR. (PRE) pre-alarm N lights pre-alarm LED and actives CBE Aspiration detector pre-alarm
ASPIR. (NON) non-fire N activates CBE Aspiration detector non-alarm
ASPIR. (REF) non-fire N activates CBE Used as a reference for other aspiration detectors on
the loop.
Note: Aspiration detector (FAAST) programming requires 5 SLC addresses. When a device associated with a FAAST device is disabled locally, all
devices associated with that FAAST will be automatically disabled as well.
ACCLIMATE
ACCL (P SUP) fire Y
(see note
below)
activates CBE Combination Photoelectric/Heat detector. Photo
element activation generates a supervisory condition
ACCL+ (P SUP) fire Y
(see note
below)
activates CBE Combination Photoelectric/Heat detector with low
temperature warning. Photo element activation
generates a supervisory condition.
For ACCL/ACCL+ detectors:
Note: Detectors programmed as ACCL (P SUP) or ACCL+ (P SUP), the heat element will latch and require a system reset to clear. The Photo
element will latch or track, depending on the ACCL (P SUP) latching setting.
1 Not suitable for Canadian applications
2 Requires approval of AHJ
3 CLIP mode only
4 LED representation of a CO alarm may be performed using an ACS annunciator
5 Photo element can be programmed as latching or tracking for all Photo/CO devices programmed as this type ID via VeriFire Tools
Table 7 Intelligent Detector Type Codes (3 of 3)
Default zone
Blinking Type Code selection
CBE list
(five zones)
12 spaces for extended
custom label
SLC number (1 or 2)
M (module)
SLC address (001-159)
PROGRAM MONITOR WESTERN ENTRANCE AND
HALLWAY 09 __ __ __ __ 2M101
20-character user-editable custom label.

Other manuals for Honeywell Notifier NFS2-640

Related product manuals