Quick Start Guide for UDC2500 Universal Digital Controller
51-52-25-124
5. Configuration Record Sheet
Enter the value or selection for each prompt on this sheet so you will have a record of how your controller was configured.
Group Prompt Function Prompt Value or
Selection
Factory
Setting
Group Prompt Function Prompt Value or
Selection
Factory
Setting
TUNING PB or GAIN
RATE T
I MIN or I RPM
MANRST
PB2 or GAIN 2
RATE2T
I2 MIN or I2 RPM
CYCT1 or CT1
X3
CYC2T2 or CT2
X3
SECUR
LOCK
AUTOMA
A TUNE
RN HLD
SP SEL
_______
_______
_______
_______
_______
_______
_______
_______
_______
_______
_______
_______
_______
_______
_______
_______
_______
1.0
0.00
1.0
1.0
0.0
0.00
1.0
20
20
20
20
0
CAL
ENAB
ENAB
ENAB
ENAB
ALGOR CTRALG TIMER
PERIOD
START
L DISP
RESET
INCRMT
_______
_______
_______
_______
_______
_______
_______
PIDA DIS
0:01
KEY
TREM
KEY
MIN
SPRAMP SPRAMP
ATI MIN
FINLSP
SPRATE
EUHRUP
EUHRDN
SPPROG
_______
_______
_______
_______
_______
_______
_______
DIS
3
1000
DIS
0
0
DIS
OUTALG OUTALG
4-20RG
CRANGE
RLY TY
_______
_______
_______
_______
(MOXL)
100
4-20
MECH
ATUNE FUZZY
TUNE
AT ERR
_______
_______
_______
DIS
TUNE
---
INPUT1 IN1TYP
XMITR1
IN1 HI
IN1 LO
RATIO1
BIAS 1
RILTR1
BRNOUT
EMIS
_______
_______
_______
_______
_______
_______
_______
_______
_______
KH
LIN
2400
0
1.00
0.0
1.0
UP
1.0
INPUT2 IN2TYP
LIN
IN2 HI
IN2 LO
RATIO2
BIAS 2
FILTR2
_______
_______
_______
_______
_______
_______
_______
1-5V
LIN
2400
0
1.00
0.0
1.0
COM ComSTA
ComADD
SDENAB
SHDTIM
BAUD
TX_DLY
WS_FLT
SDMODE
SHDSP
UNITS
CSRATO
CSP_BI
LOOPBACK
_______
_______
_______
_______
_______
_______
_______
_______
_______
_______
_______
_______
_______
Disable
0
Enable
0
9600
30
FP_B
Last
LSP
PCT
1.0
0
Disable
CONTRL PIDSET
SW VAL
LSP’S
RSPSRC
SP TRK
PWR UP
PWROUT
SP Hi
SP Lo
ACTION
OUT Hi
OUT Lo
D BAND
HYST
FAILSF
FSMODE
PBorGN
MINRPM
_______
_______
_______
_______
_______
_______
_______
_______
_______
_______
_______
_______
_______
_______
_______
_______
_______
_______
ONE
0.00
ONE
NONE
NONE
MAN
LAST
2400
0
REV
100
0
2.0
0.5
0.0
NOL
GAIN
MIN
ALARMS A1S1VA
A1S2VA
A2S1VA
A2S2VA
A1S1TY
A1S1TY
A2S1TY
A2S2TY
A1S1HL
A1S1EV
A1S2HL
A1S2EV
A2S1HL
A2S1EV
A2S2HL
A2S2EV
ALHYST
ALARM1
BLOCK
DIAG
_______
_______
_______
_______
_______
_______
_______
_______
_______
_______
_______
_______
_______
_______
_______
_______
_______
_______
_______
_______
90
90
90
90
NONE
NONE
NONE
NONE
HIGH
BEGN
HIGH
BEGN
HIGH
BEGN
HIGH
BEGN
0.0
NOL
DIS
DIS
OPTION AUXOUT
0 PCT
100 PCT
DIG IN 1
DIG1 COM
DIG IN 2
DIG2 COM
_______
_______
_______
_______
_______
_______
_______
DIS
0
100
NONE
DIS
NONE
DIS
DISPLY DECMAL UNITS
FREQ
DISPLY
LNGUAG
_______
_______
_______
_______
_______
8888
F
60
PRN
ENGL
6. Start Up Procedure for Operation
Step Operation Press Result
1 Select
Manual
Mode
M-A
RESET
N/A for Single Display Model
Until “M” indicator is ON.
The controller is in manual mode.
2 Adjust the
Output
or
N/A for Single Display Model
To adjust the output value and ensure that the final control element is functioning correctly.
Upper Display = Pv Value
Lower Display = OT and the output value in %
3 Tune the
Controller
SET UP
Make sure the controller has been configured properly and all the values and selections have been recorder on the
Configuration Record Sheet.
Refer to Tuning Set Up group to ensure that the selections for PB or GAIN, RATE T, and I MIN, or I RPM have been entered.
Use Accutune to tune the controller; see product manual for detailed procedure.
4 Enter the
Local
Setpoint
LOWER
DISPLAY
Upper Display = Pv Value
Lower Display = SP and the Local Setpoint Value
or
To adjust the local setpoint to the value at which you want the process variable maintained.
The local setpoint cannot be changed if the Setpoint Ramp function is running.
5 Select
Automatic
Mode
M-A
RESET
N/A for Single Display Model
Until “A” indicator is ON.
The controller is in Automatic mode.
The controller will automatically adjust the output to maintain the process variable at setpoint.
To Previous Page
Loading...
