EasyManuals Logo

Honeywell Xenon 1952H User Manual

Honeywell Xenon 1952H
332 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #144 background imageLoading...
Page #144 background image
126 Xenon XP User Guide
Enter prefixes and suffixes in the order in which you want them to appear on the
output.
When setting up for specific symbologies (as opposed to all symbologies), the
specific symbology ID value counts as an added prefix or suffix character.
The maximum size of a prefix or suffix configuration is 200 characters, which
includes header information.
Add a Prefix or Suffix:
Step 1. Scan the Add Prefix or Add Suffix symbol (page 127).
Step 2. Determine the 2 digit hex value from the Symbology Charts (beginning
on page 297) for the symbology to which you want to apply the prefix or
suffix. For example, for Code 128, Code ID is “j” and Hex ID is “6A”.
Step 3. Scan the 2 hex digits from the Programming Chart, beginning on page
311, or scan 9, 9 for all symbologies.
To add the Code I.D., scan 5, C, 8, 0.
To add the AIM I.D., scan 5, C, 8, 1.
To add the serial number, scan 5, C, 8, 8.
To add a backslash (\), scan 5, C, 5, C.
Note: When adding a backslash (\), you must scan 5C twice – once to create the leading
backslash and then to create the backslash itself.
Step 4. Repeat Steps 2 and 3 for every prefix or suffix character.
Step 5. Scan Save to exit and save, or scan Discard to exit without saving.
Repeat the steps above to add a prefix or suffix for another symbology.
Example: Add a Tab Suffix to All Symbologies
Step 1. Scan Add Suffix.
Step 2. Scan 9, 9 from the Programming Chart, beginning on page 311 to apply
this suffix to all symbologies.
Step 3. Scan 0, 9 from the Programming Chart, beginning on page 311. This
corresponds with the hex value for a horizontal tab, shown in the ASCII
Conversion Chart (Code Page 1252), beginning on page 300.
Step 4. Scan Save, or scan Discard to exit without saving.
Clear One or All Prefixes or Suffixes
You can clear a single prefix or suffix, or clear all prefixes/suffixes for a symbology.
If you have been entering prefixes and suffixes for single symbologies, you can use
Clear One Prefix (Suffix) to delete a specific character from a symbology. When
you Clear All Prefixes (Suffixes), all the prefixes or suffixes for a symbology are
deleted.

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Honeywell Xenon 1952H and is the answer not in the manual?

Honeywell Xenon 1952H Specifications

General IconGeneral
Storage temperature (T-T)-40 - 70 °C
Operating temperature (T-T)0 - 50 °C
Operating relative humidity (H-H)0 - 95 %
TypeHandheld bar code reader
Sensor type-
Scanner type1D/2D
Pitch reading angle-45 - 45 °
Light levels (direct sunlight)0 - 100000 lx
Linear (1D) barcodes supportedCode 128, Code 39, U.P.C.
Optical sensor resolution (W x H)1240 x 800 pixels
2D (matrix & stacked) barcodes supportedData Matrix, PDF417, QR Code
Battery life14 h
Charging time4.5 h
Battery capacity2400 mAh
Power source typeBattery
Number of reads per charge50000
Product colorWhite
LED indicatorsYes
Built-in displayNo
Housing materialPlastic
International Protection (IP) codeIP41
Wireless range10 m
Bluetooth version4.2
Operating frequency2400 MHz
Standard interfacesUSB
Connectivity technologyWired & Wireless
Harmonized System (HS) code84716070
Weight and Dimensions IconWeight and Dimensions
Depth99 mm
Width64 mm
Height165 mm
Weight220 g

Related product manuals